参数资料
型号: CS5467-ISZR
厂商: Cirrus Logic Inc
文件页数: 42/46页
文件大小: 0K
描述: IC ENERGY METERING 1PHASE 28SSOP
标准包装: 1,000
输入阻抗: 30 千欧
测量误差: 0.1%
电压 - 高输入/输出: 0.8V
电压 - 低输入/输出: 0.2V
电流 - 电源: 3.5mA
电源电压: 4.75 V ~ 5.25 V
测量仪表类型: 单相
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 28-SSOP(0.209",5.30mm 宽)
供应商设备封装: 28-SSOP
包装: 带卷 (TR)
配用: 598-1555-ND - BOARD EVAL FOR CS5467 ADC
CS5467
10. E 2 PROM OPERATION
The CS5467 can accept commands from a serial
E 2 PROM connected to the serial interface instead of a
host microcontroller. A high level (logic 1) on the MODE
input indicates that an E 2 PROM is connected. This
makes the CS and SCLK pins become driven outputs.
After reset and after running the initialization program,
the CS5467 begins reading commands from the con-
nected E 2 PROM.
10.1 E 2 PROM Configuration
A typical connection between the CS5467 and a
E 2 PROM is shown in Figure 13 .
The CS5467 asserts CS (logic 0), clocks SCLK, and
sends Read commands to the E 2 PROM on SDO.
Command format is identical to microcontroller mode,
except the CS5467 will not attempt to write to the EE-
PROM device. The command sequence stops when the
STOP bit in the Control register ( Ctrl ) is written by the
command sequence.
10.2 E 2 PROM Code
The EEPROM code should do the following:
1. Set any Configuration or Control register bits, such as
HPF enables and phase compensation settings.
2. Write any calibration data to gain and offset registers.
3. Set energy output pulse width, rate, and formats.
4. Execute a Continuous Conversion command.
5. Set the STOP bit in the Control register (last).
Below is an example E 2 PROM code set.
- 7E 00 00 01
Change to page 1.
- 60 00 01 E0
Write Modes Register, turn high-pass filters on.
- 42 7F C4 A9
Write value of 0x7FC4A9 to I1 GAIN register.
- 46 FF B2 53
Write value of 0xFFB253 to V1 GAIN register.
5K
VD
+
E1
E2
CS5467
SCLK
SDI
SDO
MODE CS
Pulse Output
Counter
5K
EEPROM
SCK
SO
SI
CS
- 50 7F C4 A9
Write value of 0x7FC4A9 to I2 GAIN register.
- 54 FF B2 53
Write value of 0xFFB253 to V2 GAIN register.
- 7E 00 00 00
Change to page 0.
- 74 00 00 04
Set LSD bit to 1 in the Mask register.
- E8
Start continuous conversions
Connector to Calibrator
Figure 13. Typical Interface of E 2 PROM to CS5467
Figure 13 also shows the external connections that
would be made to a calibration device, such as a note-
book computer, handheld calibrator, or tester during
- 78 00 01 00
Write STOP bit to the Control register ( Ctrl ) to
terminate E 2 PROM command sequence.
10.3 Which E 2 PROMs Can Be Used?
Several industry-standard serial E 2 PROMs can be used
with the CS5467. Some are listed below:
meter assembly, The calibrator or tester can be used to
control the CS5467 during calibration and program the
required values into the E 2 PROM.
?
?
?
Atmel AT25010, AT25020 or AT25040
National Semiconductor NM25C040M8 or NM25020M8
Xicor X25040SI
These serial E 2 PROMs expect a specific 8-bit com-
mand (00000011) in order to perform a memory read.
The CS5467 has been hardware programmed to trans-
mit this 8-bit command to the E 2 PROM after reset.
42
DS714F3
相关PDF资料
PDF描述
AISC-0402-1NOJ-T INDUCTOR WW CERAM 1.0NH 0402
S5KC-13 RECTIFIER GPP SMD 800V 5A SMC
ACC43DRXH CONN EDGECARD 86POS .100 DIP SLD
GSA50DTMZ-S664 CONN EDGECARD 100PS R/A .125 SLD
A7PSB-1510M CABLE D-SUB-AMM15B/AE15M/AFM15B
相关代理商/技术参数
参数描述
CS5471 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:DUAL CHANNEL DELTA SIGMA ANALOG TO DIGITAL CONVERTER
CS5471-BS 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Cirrus Logic 功能描述:
CS5471-BSR 制造商:Rochester Electronics LLC 功能描述:- Bulk
CS547233-ISZR 功能描述:模数转换器 - ADC IC 24-bit 2-ch Delta Sigma ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
CS547239-ISZ 制造商:Cirrus Logic 功能描述:C 24-BIT 2-CH DELTA SIGMA ADC - Bulk