参数资料
| 型号： | CS8130-CS |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC IR TRANSCEIVER 2-5V 20-SSOP |
| 标准包装： | 66 |
| 类型： | 收发器 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 758 (CN2011-ZH PDF) |
| 配用： | 598-1161-ND - BOARD EVAL FOR CS8130 |
| 其它名称： | 598-1203-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Grounding & Layout
Grounding and layout for the CS8130 are criti-
cal, because of the sensitive nature of the PIN
diode amplifier. The CS8130 should be over its
own dedicated ground plane. The PIN diode
should be very close to the PINA and PINC
pins. The PIN diode traces should be very short
(< 5 mm), and should be surrounded by ground
plane. There should be holes in the ground plane
provided for mounting a metal shield over the
CS8130 and the PIN diode for EMI shielding.
The PIN diode and transmit LEDs should be po-
sitioned so as to line up the front optical surfaces
of the packages. The optical surface of the PIN
diode and transmit LED(s) should be positioned
1cm back from the daylight IR filter window in-
side the case of the equipment. This ensures that
direct sunlight does not fall upon the top surface
of the PIN diode.
An evaluation kit, CDB8130, is available from
Crystal. This may be used as an example of the
correct layout for the CS8130 and the optical
components.
Optical Components
TEMIC (Tel: 408 970 5684) provides Telefunken
infrared LEDs and PIN diodes which are com-
patible with the CS8130. Contact Crystal for
details of additional qualified LED and PIN di-
ode sources.
Example Application Schematics
Crystal has prepared some example schematics
which demonstrate possible uses for the CS8130.
Figure 8 shows a computer or PDA motherboard
example, where one UART is used to drive both
a wired RS232 COM port and an IR port.
Figure 9 shows a pod schematic. This is an ex-
ternal unit which can be plugged into any
existing COM port to create an IR port.
Schematic & Layout Review Service
Confirm Optimum
Schematic & Layout
Before Building Your Board.
For Our Free Review Service
Call Applications Engineering.
Call: (512) 445-7222
CS8130
22
DS134PP2
CS8130
22
DS134F1
相关PDF资料 |
PDF描述 |
|---|---|
| CS8190EDWF20G | IC TACH/SPEEDO DRVR PREC 20SOICW |
| CS8191XNF16 | IC DRVR AIRCORE TACH/SPEED 16DIP |
| CS82C5296 | IC UART/BRG 5V 16MHZ 28-PLCC |
| CS82C59A-1296 | IC CTRL INTERRUPT 12.5MHZ 28PLCC |
| CS8900A-IQZ | IC LAN ETHERNET CTLR 5V 100LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS8130-CSR | 功能描述:红外收发器 IC Multi-Standard Infrared Transceiver RoHS:否 制造商:Vishay Semiconductors 波长:900 nm 连续数据传输:115.2 Kbit/s 传输距离:1 m 辐射强度:60 mW/sr 半强度角度:44 deg 脉冲宽度:2 us 最大上升时间:100 ns 最大下降时间:100 ns LED 电源电压:- 0.5 V to 6 V 最大正向电流:80 mA 工作电压:2.4 V to 5.5 V 最大工作温度:+ 85 C 最小工作温度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封装 / 箱体: 封装:Reel |
| CS8130-CSZ | 功能描述:红外收发器 IC Multi-Standard Infrared Transceiver RoHS:否 制造商:Vishay Semiconductors 波长:900 nm 连续数据传输:115.2 Kbit/s 传输距离:1 m 辐射强度:60 mW/sr 半强度角度:44 deg 脉冲宽度:2 us 最大上升时间:100 ns 最大下降时间:100 ns LED 电源电压:- 0.5 V to 6 V 最大正向电流:80 mA 工作电压:2.4 V to 5.5 V 最大工作温度:+ 85 C 最小工作温度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封装 / 箱体: 封装:Reel |
| CS8130-CSZR | 功能描述:红外收发器 IC Multi-Standard Infrared Transceiver RoHS:否 制造商:Vishay Semiconductors 波长:900 nm 连续数据传输:115.2 Kbit/s 传输距离:1 m 辐射强度:60 mW/sr 半强度角度:44 deg 脉冲宽度:2 us 最大上升时间:100 ns 最大下降时间:100 ns LED 电源电压:- 0.5 V to 6 V 最大正向电流:80 mA 工作电压:2.4 V to 5.5 V 最大工作温度:+ 85 C 最小工作温度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封装 / 箱体: 封装:Reel |
| CS8130-IS | 制造商:Cirrus Logic 功能描述:IRDA TX/RX 0.1152MBPS 2.7V TO 5.5V 20SSOP - Rail/Tube |
| CS8130-ISR | 制造商:Cirrus Logic 功能描述:IRDA TX/RX 0.1152MBPS 2.7V TO 5.5V 20SSOP - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。