- 您现在的位置：买卖IC网 > PDF目录11818 > CS82C50A-5Z (Intersil)IC COMMUNICATION ELEMENT 44-PLCC PDF资料下载
参数资料
| 型号： | CS82C50A-5Z |
| 厂商： | Intersil |
| 文件页数： | 21/25页 |
| 文件大小： | 0K |
| 描述： | IC COMMUNICATION ELEMENT 44-PLCC |
| 标准包装： | 26 |
| 特点： | 单芯片 UART/BRG |
| 通道数： | 1，UART |
| 规程： | RS232C |
| 电源电压： | 4.5 V ~ 5.5 V |
| 带并行端口： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 管件 |
| 产品目录页面： | 1242 (CN2011-ZH PDF) |
5
FN2958.5
August 24, 2006
82C50A
OUT1
34
O
L
OUTPUT 1: This is a general purpose output that can be programmed ACTIVE (low) by
settingVCR(2) (OUT1) of the Modem Control Register to a high level. The OUT1 pin is
set high by Master Reset. The OUT1 pin is INACTIVE (high) during loop mode operation.
OUT2
31
O
L
OUTPUT 2: This is a general purpose output that can be programmed ACTIVE (low) by
setting MCR(3) (OUT1) of the Modem Control Register to a high level. The OUT2 pin is
set high by Master Reset. The OUT2 signal is INACTIVE (high) during loop mode
operation.
RI
39
1
L
RING INDICATOR: When low, RI indicates that a telephone ringing signal has been
received by the modem or data set. The RI signal is a modem control input whose
condition is tested by reading MSR(6) (RI). The Modem Status Register output TERI
(MSR(2)) indicates whether the RI input has changed from a Low to High since the
previous reading of the MSR. If the interrupt is enabled (IER (3) = 1) and RI changes from
a Low to High, an interrupt is generated. The ACTIVE (low) state of RI indicates that the
DCE is receiving a ringing signal. RI will appear ACTIVE for approximately the same
length of time as the ACTIVE segment of the ringing cycle. The INACTIVE state of RI will
occur during the INACTIVE segments not detected by the DCE. This circuit is not
disabled by the INACTIVE condition of DTR.
DCD
38
I
L
DATA CARRIER DETECT: When ACTIVE (low), DCD indicates that the data carrier has
been detected by the modem or data set. DCD is a modem input whose condition can
be tested by the CPU by reading MSR(7) (DCD) of the Modem Status Register. MSR(3)
(DDCD) of the Modem Status Register indicates whether the DCD input has changed
since the previous reading of the MSR. DOD has no effect on the receiver. If the DCD
changes state with the modem status interrupt enabled, an interrupt is generated.
When DCD is ACTIVE (low), the received line signal from the remote terminal is within
the limits specified by the DCE manufacturer. The INACTIVE (high) signal indicates that
the signal is not within the specified limits, or is not present.
MR
35
1
H
MASTER RESET: The MR input forces the 82C50A into an idle mode in which all serial
data activities are suspended. The Modem Control Register (MCR) along with its
associated outputs are cleared. The Line Status Register (LSR) is cleared except for the
THRE and TEMT bits, which are set. The 82C50A remains in an idle state until
programmed to resume serial data activities. The MR input is a Schmitt trigger input. See
the DC Electrical Characteristics for Schmitt trigger logic input voltage levels. See Table
7 for a summary of Master Reset’s effect on 82C50A operation.
lNTRPT
30
O
H
INTERRUPT REQUEST: The lNTRPT output goes ACTIVE (high) when one of the
following interrupts has an ACTIVE (high) condition and is enabled by the Interrupt
Enable Register: Receiver Error flag, Received Data Available, Transmitter Holding
Register Empty, and Modem Status. The lNTRPT is reset low upon appropriate service
or a MR operation. See Figure 1. Interrupt Control Structure.
SIN
10
I
H
SERIAL DATA INPUT: The SIN input is the serial data input from the communication line
or modem to the 82C50A receiver circuits. A mark (1) is high, and a space (0) is low. Data
inputs on SIN are disabled when operating in the loop mode.
VCC
40
H
VCC: +5V positive power supply pin. A 0.1μA decoupling capacitor from VCC (pin 40)
to GND (pin 20) is recommended.
CS0, CS1,
CS2
12,13,
14
I
H, H,
L
CHIP SELECT: The Chip Select inputs act as enable signals for the write (DOSTR,
DOSTR) and read (DlSTR, DlSTR) input signals. The Chip Select inputs are latched by
the ADS input.
NC
29
Do Not Connect
CSOUT
24
O
H
CHIP SELECT OUT: When ACTIVE (high), this pin indicates that the chip has been
selected by active CS0, CS1, and CS2 inputs. No data transfer can be initiated until
CSOUT is a logic 1, ACTIVE (high).
DDIS
23
O
H
DRIVER DISABLE: This output is INACTIVE (low) when the CPU is reading data from
the 82C50A. An ACTIVE (high) Dells output can be used to disable an external
transceiver when the CPU is reading data.
ADS
25
I
L
ADDRESS STROBE: When ACTIVE (low), ADS latches the Register Select (A0, A1,
A2) and Chip Select (CS0, CS1, CS2) inputs. An active ADS is required when the
Register Select pins are not stable for the duration of the read or write operation,
multiplexed mode. If not required, the ADS input should be tied low, non-multiplexed
mode.
RCLK
9
I
This input is the 16X Baud Rate Clock for the receiver section of the 82C50A. This input
may be provided from the BAUDOUT output or an external clock.
Pin Description (Continued)
SYMBOL
PIN
NUMBER
TYPE
ACTIVE
LEVEL
DESCRIPTION
相关PDF资料 |
PDF描述 |
|---|---|
| CP82C52Z | IC UART/BRG 5V 16MHZ 28-PDIP |
| ATUC128D4-AUR | IC MCU 32BIT 128KB FLASH 48TQFP |
| VI-B72-IW-F2 | CONVERTER MOD DC/DC 15V 100W |
| V24C12H150B2 | CONVERTER MOD DC/DC 12V 150W |
| VI-B71-IX-F3 | CONVERTER MOD DC/DC 12V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS82C50A-5Z96 | 功能描述:UART 接口集成电路 W/ANNEAL 44 PLCC 0+7 0C 5 0V 10 0MHZ RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| CS82C52 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS82C5296 | 功能描述:IC UART/BRG 5V 16MHZ 28-PLCC RoHS:否 类别:集成电路 (IC) >> 接口 - UART（通用异步接收器/发送器） 系列:- 标准包装:250 系列:- 特点:* 通道数:2，DUART FIFO's:16 字节 规程:RS232，RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:托盘 其它名称:XR16L2551IM-F-ND |
| CS82C52Z | 功能描述:UART 接口集成电路 A/ANNEAL PERIPH UART /BRG 5V 16MHZ 28PLCC RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| CS82C52Z96 | 功能描述:UART 接口集成电路 A/ANNEAL PERIPH UART /BRG 5V 16MHZ 28PLCC RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。