- 您现在的位置：买卖IC网 > Datasheet目录218 > CUB5IB00 (Red Lion Controls)DC METER RED/GREEN BKLT Datasheet资料下载
参数资料
| 型号： | CUB5IB00 |
| 厂商： | Red Lion Controls |
| 文件页数： | 4/12页 |
| 文件大小： | 0K |
| 描述： | DC METER RED/GREEN BKLT |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | RLC170 |
3.0 I NSTALLING P LUG -I N C ARDS
The Plug-in cards are separately purchased option cards that perform specific
functions. The cards plug into the main circuit board of the meter
Range Jumpers
Setpoint Card
Comms or
Programming
Card
CAUTION: The Plug-in cards and main circuit board contain static
sensitive components. Before handling the cards, discharge
static charges from your body by touching a grounded bare
metal object. Ideally, handle the cards at a static controlled
clean workstation. Also, only handle the cards by the edges.
Dirt, oil or other contaminants that may contact the cards can
adversely affect circuit operation.
REMOVING THE REAR COVER
To remove the rear cover, locate the cover locking tab below the 2nd and 3rd
input terminals. To release the tab, insert a small, flat blade screwdriver between
the tab and the plastic wall below the terminals. Inserting the screwdriver will
provide enough pressure to release the tab locks. To replace the cover, align the
cover with the input terminals and press down until the cover snaps into place .
Locking Tab
4.0 W IRING
THE
M ETER
WIRING OVERVIEW
Electrical connections are made via screw-clamp terminals located on the
back of the meter. All conductors should conform to the meter ’s voltage and
current ratings. All cabling should conform to appropriate standards of good
installation, local codes and regulations. It is recommended that the power
supplied to the meter (DC or AC) be protected by a fuse or circuit breaker.
Strip the wire, leaving approximately 0.3" (7.5 mm) bare lead exposed
(stranded wires should be tinned with solder.) Insert the lead under the correct
screw-clamp terminal and tighten until the wire is secure. (Pull wire to verify
tightness.) Each terminal can accept up to one #14 AWG (2.55 mm) wire, two
#18 AWG (1.02 mm), or four #20 AWG (0.61 mm).
EMC INSTALLATION GUIDELINES
Although Red Lion Controls Products are designed with a high degree of
immunity to Electromagnetic Interference (EMI), proper installation and wiring
methods must be followed to ensure compatibility in each application. The type
of the electrical noise, source or coupling method into a unit may be different
for various installations. Cable length, routing, and shield termination are very
important and can mean the difference between a successful or troublesome
installation. Listed are some EMI guidelines for a successful installation in an
industrial environment.
1. A unit should be mounted in a metal enclosure, which is properly connected
to protective earth.
2. Use shielded cables for all Signal and Control inputs. The shield connection
should be made as short as possible. The connection point for the shield
depends somewhat upon the application. Listed below are the recommended
methods of connecting the shield, in order of their effectiveness.
a. Connect the shield to earth ground (protective earth) at one end where the
unit is mounted.
b. Connect the shield to earth ground at both ends of the cable, usually when
the noise source frequency is over 1 MHz.
3. Never run Signal or Control cables in the same conduit or raceway with AC
power lines, conductors, feeding motors, solenoids, SCR controls, and
heaters, etc. The cables should be run through metal conduit that is properly
grounded. This is especially useful in applications where cable runs are long
4.1 POWER WIRING
DC Power
and portable two-way radios are used in close proximity or if the installation
is near a commercial radio transmitter. Also, Signal or Control cables within
an enclosure should be routed as far away as possible from contactors,
control relays, transformers, and other noisy components.
4. Long cable runs are more susceptible to EMI pickup than short cable runs.
5. In extremely high EMI environments, the use of external EMI suppression
devices such as Ferrite Suppression Cores for signal and control cables is
effective. The following EMI suppression devices (or equivalent) are
recommended:
Fair-Rite part number 0443167251 (RLC part number FCOR0000)
Line Filters for input power cables:
Schaffner # FN2010-1/07 (Red Lion Controls # LFIL0000)
6. To protect relay contacts that control inductive loads and to minimize radiated
and conducted noise (EMI), some type of contact protection network is
normally installed across the load, the contacts or both. The most effective
location is across the load.
a. Using a snubber, which is a resistor-capacitor (RC) network or metal oxide
varistor (MOV) across an AC inductive load is very effective at reducing
EMI and increasing relay contact life.
b. If a DC inductive load (such as a DC relay coil) is controlled by a transistor
switch, care must be taken not to exceed the breakdown voltage of the
transistor when the load is switched. One of the most effective ways is to
place a diode across the inductive load. Most RLC products with solid
state outputs have internal zener diode protection. However external diode
protection at the load is always a good design practice to limit EMI.
Although the use of a snubber or varistor could be used.
RLC part numbers: Snubber: SNUB0000
Varistor: ILS11500 or ILS23000
7. Care should be taken when connecting input and output devices to the
instrument. When a separate input and output common is provided, they
should not be mixed. Therefore a sensor common should NOT be connected
to an output common. This would cause EMI on the sensitive input common,
which could affect the instrument’s operation.
Visit RLC’s web site at http://www.redlion.net/Support/InstallationConsiderations.
html for more information on EMI guidelines, Safety and CE issues as they
relate to Red Lion Controls products.
4.2 USER INPUT WIRING
Sinking Logic
}
+9 to +28 VDC: +VDC
Power Common: -VDC
USR COMM
USR
Connect external switching device between the
User Input terminal and User Input Common.
The user input of the meter is
CAUTION : 9 to 28 VDC
power circuit is not isolated
from the signal circuit.
PWR COMMON
-
+
+9-28 VDC
internally pulled up to +9 to +28 V
with 10 K resistance. The input is
active when it is pulled low (<0 .7 V).
4
PWR COMMON
+9-28 VDC
相关PDF资料 |
PDF描述 |
|---|---|
| CUB5PB00 | PROCESS METER RED/GREEN BKLT |
| CUB5RTR0 | RTD METER REFLECTIVE |
| CUB5TCB0 | METER PANEL LCD THERMOCOUPLE RED |
| CUB5USB0 | USB OPTION CARD |
| CUB5VR00 | METER LCD DC VOLT 8DIGIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CUB5IB00 CALIBRATED | 制造商:Red Lion Controls 功能描述:DIGITAL PANEL METER MODEL CUB5 WITH CERTIFICATE OF CALIBRATION |
| CUB5IR00 | 功能描述:DC METER REFLECTIVE DISP RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030 |
| CUB5OEMS | 制造商:Red Lion Controls 功能描述:PROGRAMMING KIT FOR SOFTWARE |
| CUB5PB00 | 功能描述:PROCESS METER RED/GREEN BKLT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030 |
| CUB5PR00 | 功能描述:PROCESS METER REFLECTIVE RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030 |
发布紧急采购，3分钟左右您将得到回复。