- 您现在的位置：买卖IC网 > Datasheet目录620 > CUB7P200 (Red Lion Controls)HSPEED LOGIC INPUT CNTR POS Datasheet资料下载
参数资料
| 型号： | CUB7P200 |
| 厂商： | Red Lion Controls |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | HSPEED LOGIC INPUT CNTR POS |
| 标准包装： | 1 |
| 系列： | CUB7 |
| 计数速率： | 10kHz |
| 数字/字母数： | 8 |
| 输入类型： | 逻辑，晶体管 |
| 电源电压： | 不需要（包括电池） |
| 显示器类型： | LCD 无背光 |
| 其它名称： | Q1688270 |
USING THE OPTIONAL TERMINAL BLOCK
1. Remove the rear cover. Refer to Figure 1. A small slotted screwdriver is
required to release the side latches. Insert the screwdriver tip between the
rear cover and the side of the unit. Leverage the screwdriver away from the
case to unlatch the side latch and slightly lift the rear cover. Pinch the
corners to hold the rear cover in place. Remove the screwdriver and repeat
the same procedure on the other side of the rear cover. When both side
latches are released, slide the rear cover from the unit and the wires.
2. For safety concerns, the wires should be cut off completely flush with the PC
board to prevent a short.
3. Break out the break away tab(s) as required. Remove the left tab only for 3
position terminal block or both tabs for 4 and 5 position terminal blocks.
4. Reinstall the rear cover into CUB7 unit.
5. Mount the CUB7 into the panel (refer to 1.0 Installing The Meter)
6. Push the keyed terminal block onto the exposed PC board. The left most
terminal, next to the DIP switch(s) is terminal #1.
Note: Wire sizes 16-24 AWG may be used with 0.25" length exposed. The
screwless type terminal block requires a small slotted screwdriver engaged in
the upper slot to open the wire clamp in the lower larger slot. Removing the
screwdriver will lock the wire clamp unto the wire.
Side
Latches
Figure 1
Rear Cover
Mounting Clip
DIP Switch(s)
Cut Wires Internally
(If using Optional
Terminal Block)
Wires must be cut off completely
flush with PC board.
Side Latches
Break-out Tab or Tabs
(If using Optional
Terminal Block)
Open & Lock
Wire Clamp
Optional
Terminal Block
Terminal #1
Current Sinking Output
Current Sourcing Output
Logic Output
ON
*
1 2 3
1
2
3
4
+
?
Optional
Backlight
Power
ON
*
1 2 3
+V
1
2
3
4
+
?
Optional
Backlight
Power
ON
*
1 2 3
1
2
3
4
+
?
Optional
Backlight
Power
Switch/Contact Sinking Output
Switch/Contact Sourcing Output
High Voltage
ON
*
1 2 3
1
2
3
4
+
?
Optional
Backlight
Power
ON
*
1 2 3
+V
1
2
3
4
+
?
Optional
Backlight
Power
ON
*
3
50-250
VDC/VAC
1
2
3
4
5
+
?
Optional
Backlight
Power
Switch position is application dependent.
6
Shaded area for high voltage applications.
相关PDF资料 |
PDF描述 |
|---|---|
| CUB7T000 | TIMER LCD PROGRAM 8 DIGIT |
| CUB7W020 | COUNTER 8-DIGIT RED BKLT VOLT-IN |
| D-659-0001 | TOOL REMOVAL MTC CONN WAFER |
| D7-1 | DIE, .041 HOLE DIA |
| DH2X61-18A | DIODE FST REC 1800V2X60A SOT227B |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CUB7P210 | 功能描述:COUNTER 8-DIGIT LOGIC GREEN RoHS:是 类别:工业控制，仪表 >> 计数器 系列:CUB7 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮 |
| CUB7P220 | 功能描述:COUNTER 8-DIGIT LOGIC RED RoHS:是 类别:工业控制，仪表 >> 计数器 系列:CUB7 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮 |
| CUB7P300 | 功能描述:COUNTER 8-DIGIT LV REFLECTIVE RoHS:是 类别:工业控制，仪表 >> 计数器 系列:CUB7 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮 |
| CUB7P310 | 功能描述:COUNTER 8-DIGIT LV GRN BACKLIGHT RoHS:是 类别:工业控制，仪表 >> 计数器 系列:CUB7 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮 |
| CUB7P320 | 功能描述:COUNTER 8-DIGIT LV RED BACKLIGHT RoHS:是 类别:工业控制，仪表 >> 计数器 系列:CUB7 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮 |
发布紧急采购，3分钟左右您将得到回复。