- 您现在的位置：买卖IC网 > PDF目录17061 > DC1010A-A (Linear Technology)BOARD DELTA SIGMA ADC LTC2493 PDF资料下载
参数资料
| 型号： | DC1010A-A |
| 厂商： | Linear Technology |
| 文件页数： | 6/32页 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2493 |
| 软件下载： | QuikEval System |
| 设计资源： | DC1010A Design File DC1010A Schematic |
| 标准包装： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的数量： | 1 |
| 位数： | 24 |
| 采样率（每秒）： | 15 |
| 数据接口： | I²C，串行 |
| 已用 IC / 零件： | LTC2493 |
| 已供物品： | 板 |
| 相关产品： | LTC2493IDE#TRPBF-ND - IC ADC 24BIT DELTA SIG 14-DFN LTC2493CDE#TRPBF-ND - IC ADC 24BIT DELTA SIG 14-DFN LTC2493CDE#PBF-ND - IC ADC 24BIT DELTA SIG 14-DFN LTC2493IDE#PBF-ND - IC ADC 24BIT DELTA SIG 14-DFN |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC2493
14
2493fd
signals to swing beyond ground and VCC. Moreover, the
cancellation does not interfere with the transparent offset
and full-scale auto-calibration and the absolute accuracy
(full-scale + offset + linearity + drift) is maintained even
with external RC networks.
Power-Up Sequence
The LTC2493 automatically enters an internal reset state
when the power supply voltage, VCC, drops below ap-
proximately 2.0V. This feature guarantees the integrity of
the conversion result and input channel selection.
WhenVCCrisesabovethisthreshold,theconvertercreates
an internal power-on reset (POR) signal with a duration
of approximately 4ms. The POR signal clears all internal
registers. The conversion immediately following a POR
cycle is performed on the input channel IN+ = CH0, IN– =
CH1withsimultaneous50Hz/60Hzrejectionand1xoutput
rate. The first conversion following a POR cycle is accurate
within the specification of the device if the power supply
voltage is restored to (2.7V to 5.5V) before the end of the
POR interval. A new input channel, rejection mode, speed
mode, or temperature selection can be programmed into
the device during this first data input/output cycle.
Reference Voltage Range
This converter accepts a truly differential external refer-
ence voltage. The absolute/common mode voltage range
for the REF+ and REF– pins covers the entire operating
range of the device (GND to VCC). For correct converter
operation, VREF must be positive (REF+ > REF–).
The LTC2493 differential reference input range is 0.1V to
VCC. For the simplest operation, REF+ can be shorted to
VCC and REF– can be shorted to GND. The converter out-
put noise is determined by the thermal noise of the front
end circuits and, as such, its value in nanovolts is nearly
constant with reference voltage. A decrease in reference
voltage will not significantly improve the converter’s effec-
tive resolution. On the other hand, a decreased reference
will improve the converter’s overall INL performance.
Input Voltage Range
The analog inputs are truly differential with an absolute,
commonmoderangefortheCH0-CH3andCOMinputpins
extending from GND – 0.3V to VCC + 0.3V. Outside these
limits, the ESD protection devices begin to turn on and
the errors due to input leakage current increase rapidly.
Within these limits, the LTC2493 converts the bipolar dif-
ferential input signal VIN = IN+ – IN– (where IN+ and IN–
are the selected input channels), from –FS = –0.5 VREF
to +FS = 0.5 VREF where VREF = REF+ - REF–. Outside this
range, the converter indicates the overrange or the under-
range condition using distinct output codes (see Table 1).
In order to limit any fault current, resistors of up to 5k
may be added in series with the input. The effect of series
resistanceontheconverteraccuracycanbeevaluatedfrom
the curves presented in the Input Current/Reference Cur-
rent sections. In addition, series resistors will introduce a
temperature dependent error due to input leakage current.
A 1nA input leakage current will develop a 1ppm offset
error on a 5k resistor if VREF = 5V. This error has a very
strong temperature dependency.
I2C INTERFACE
The LTC2493 communicates through an I2C interface. The
I2C interface is a 2-wire open-drain interface supporting
multiple devices and multiple masters on a single bus. The
connected devices can only pull the data line (SDA) low
and can never drive it high. SDA is required to be exter-
nally connected to the supply through a pull-up resistor.
When the data line is not being driven, it is high. Data on
the I2C bus can be transferred at rates up to 100kbits/s
in the standard mode and up to 400kbits/s in the fast
mode. The VCC power should not be removed from the
device when the I2C bus is active to avoid loading the
I2C bus lines through the internal ESD protection diodes.
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate either as a
transmitter or receiver, depending on the function of the
device. In addition to transmitters and receivers, devices
canalsobeconsideredasmastersorslaveswhenperform-
ing data transfers. A master is the device which initiates a
data transfer on the bus and generates the clock signals
applicaTions inForMaTion
相关PDF资料 |
PDF描述 |
|---|---|
| RCM15DCAH-S189 | CONN EDGECARD 30POS R/A .156 SLD |
| ECC31DJCN | CONN EDGECARD 62PS .100 PRESSFIT |
| DEMO9S08QB8 | BOARD DEMO FOR 9S08 QB MCU |
| DC951A | BOARD DELTA SIGMA ADC LTC2481 |
| EBC28DCAI | CONN EDGECARD 56POS R/A .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1010A-B | 功能描述:BOARD DELTA SIGMA ADC LTC2489 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:Easy Drive™, QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1010A-C | 功能描述:BOARD DELTA SIGMA ADC LTC2487 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:Easy Drive™, QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1010CA | 制造商:DIGITAL 功能描述: |
| DC1010EL07 WAF | 制造商:ON Semiconductor 功能描述: |
| DC-101-1 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:1 WATT SINGLE OUTPUT DC-DC CONVERTERS |
发布紧急采购，3分钟左右您将得到回复。