- 您现在的位置：买卖IC网 > PDF目录20406 > DC1195A (Linear Technology)BOARD DEMO LTM8023 PDF资料下载
参数资料
| 型号： | DC1195A |
| 厂商： | Linear Technology |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO LTM8023 |
| 软件下载： | LTM8023 Spice Model |
| 设计资源： | DC1195A Schematic |
| 标准包装： | 1 |
| 系列： | µModule® |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 3.3V |
| 电流 - 输出： | 2A |
| 输入电压： | 5 ~ 36 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 600kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM8023 |
| 相关产品： | LTM8023MPV#PBF-ND - IC BUCK SYNC ADJ 2A 50LGA LTM8023IV#PBF-ND - IC BUCK SYNC ADJ 2A 50LGA LTM8023EV#PBF-ND - IC BUCK SYNC ADJ 2A 50LGA |
LTM8023
APPLICATIONS INFORMATION
Ceramic capacitors are also piezoelectric. In Burst Mode
operation, the LTM8023’s switching frequency depends
on the load current, and can excite a ceramic capacitor
at audio frequencies, generating audible noise. Since the
LTM8023 operates at a lower current limit during Burst
Mode operation, the noise is typically very quiet to a
casual ear.
If this audible noise is unacceptable, use a high performance
electrolytic capacitor at the output. The input capacitor can
be a parallel combination of a 2.2μF ceramic capacitor and
a low cost electrolytic capacitor.
A final precaution regarding ceramic capacitors concerns
the maximum input voltage rating of the LTM8023. A
ceramic input capacitor combined with trace or cable
inductance forms a high Q (under damped) tank circuit.
If the LTM8023 circuit is plugged into a live supply, the
input voltage can ring to twice its nominal value, possi-
bly exceeding the device’s rating. This situation is easily
avoided; see the Hot-Plugging Safely section.
Frequency Selection
The LTM8023 uses a constant frequency PWM architecture
that can be programmed to switch from 200kHz to 2.4MHz
by using a resistor tied from the R T pin to ground. Table 2
provides a list of R T resistor values and their resultant
frequencies.
Table 2. Switching Frequency vs R T Value
SWITCHING FREQUENCY (MHz) R T VALUE (kΩ)
0.2 187
0.3 124
0.4 88.7
0.5 69.8
0.6 56.2
0.7 46.4
0.8 39.2
0.9 34.6
1.0 29.4
1.2 23.7
1.4 19.6
1.6 15.8
1.8 13.3
2.0 11.5
2.2 9.76
2.4 8.66
Operating Frequency Tradeoffs
It is recommended that the user apply the optimal R T
value given in Table 1 for the input and output operating
condition. System level or other considerations, however,
may necessitate another operating frequency. While the
LTM8023 is flexible enough to accommodate a wide range
of operating frequencies, a haphazardly chosen one may
result in undesirable operation under certain operating or
fault conditions. A frequency that is too high can reduce
efficiency, generate excessive heat or even damage the
LTM8023 if the output is overloaded or short circuited. A
frequency that is too low can result in a final design that has
too much output ripple or too large of an output capacitor.
The maximum frequency (and attendant R T value) at which
the LTM8023 should be allowed to switch is given in Table 1
in the f (MAX) column, while the recommended frequency
(and R T value) for optimal efficiency over the given input
condition is given in the f OPTIMAL column.
There are additional conditions that must be satisfied if
the synchronization function is used. Please refer to the
Synchronization section for details.
BIAS Pin Considerations
The BIAS pin is used to provide drive power for the internal
power switching stage and operate internal circuitry. For
proper operation, it must be powered by at least 2.8V. If
the output voltage is programmed to be 2.8V or higher,
simply tie BIAS to V OUT . If V OUT is less than 2.8V, BIAS
can be tied to V IN or some other voltage source. In all
cases, ensure that the maximum voltage at the BIAS pin
is both less than 16V and the sum of V IN and BIAS is less
than 56V. If BIAS power is applied from a remote or noisy
voltage source, it may be necessary to apply a decoupling
capacitor locally to the LTM8023.
8023fi
For more information www.linear.com/LTM8023
11
相关PDF资料 |
PDF描述 |
|---|---|
| MSS1P3-E3/89A | DIODE SCHOTTKY 1A 30V MICROSMP |
| 78F470J-RC | CHOKE CONFORMAL COATED 47UH |
| AT26DF161A-SSU | IC FLASH 16MBIT 70MHZ 8SOIC |
| BAT54AT-7 | DIODE SCHOTTKY 30V 200MA SOT-523 |
| 1487E120 | WIREWAY PULL THGH 120" 8X8" GREY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1198A-A | 功能描述:BOARD EVAL LTM4605 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:µModule® 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| DC1198A-B | 功能描述:BOARD DEMO LTM4607 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:LTM®, uModule® 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| DC1198B-A | 制造商:Linear Technology 功能描述:BOARD DEMO LTM4605EV 制造商:Linear Technology 功能描述:DEMO BOARD, LTM4605 BUCK/BOOST REGULATOR, Silicon Manufacturer:Linear Technology, Silicon Core Number:LTM4605, Kit Application Type:Power Management - Voltage Regulator, Application Sub Type:Buck/Boost Regulator , RoHS Compliant: NA |
| DC1198B-B | 制造商:Linear Technology 功能描述:BOARD DEMO LTM4607EV 制造商:Linear Technology 功能描述:DEMO BOARD, LTM4607 BUCK/BOOST REGULATOR 制造商:Linear Technology 功能描述:DEMO BOARD, LTM4607 BUCK/BOOST REGULATOR, Silicon Manufacturer:Linear Technology, Silicon Core Number:LTM4607, Kit Application Type:Power Management - Voltage Regulator, Application Sub Type:Buck/Boost Regulator , RoHS Compliant: NA |
| DC119R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。