参数资料
型号: DC1385A
厂商: Linear Technology
文件页数: 6/20页
文件大小: 0K
描述: BOARD EVAL LTM4614
软件下载: LTM4614
设计资源: DC1385A Design Files
DC1385A Schematic
标准包装: 1
系列: µModule®
主要目的: DC/DC,步降
输出及类型: 2,非隔离
输出电压: 1.2V,1.8V
电流 - 输出: 4A,4A
输入电压: 2.375 ~ 5.5V
稳压器拓扑结构: 降压
频率 - 开关: 1.25MHz
板类型: 完全填充
已供物品:
已用 IC / 零件: LTM4614
相关产品: LTM4614IV#PBF-ND - IC UMODULE DC/DC DUAL 4A 144LGA
LTM4614EV#PBF-ND - IC UMODULE DC/DC DUAL 4A 144LGA
LTM4614
PIN FUNCTIONS
Slave operation is performed by putting a resistor divider
from the master output to the ground, and connecting the
center point of the divider to this pin on the slave regulator.
If tracking is not desired, then connect the TRACK pin to
V IN . Load current must be present for tracking. See the
Applications Information section.
FB1, FB2 (L6, E6): The Negative Input of the Switching
Regulators’ Error Amplifier. Internally, these pins are con-
nected to V OUT with a 4.99k precision resistor. Different
output voltages can be programmed with an externally
connected resistor between the FB and GND pins. Two
power modules can current share when this pin is con-
nected in parallel with the adjacent module’s FB pin. See
the Applications Information section.
COMP1, COMP2 (L5, E5): Current Control Threshold
and Error Amplifier Compensation Point. The current
comparator threshold increases with this control voltage.
Two power modules can current share when this pin is
connected in parallel with the adjacent module’s COMP
pin. Each channel has been internally compensated. See
the Applications Information section.
SIMPLIFIED BLOCK DIAGRAM
PGOOD1, PGOOD2 (L4, E4): Output Voltage Power
Good Indicator. Open-drain logic output that is pulled to
ground when the output voltage is not within ±7.5% of
the regulation point.
RUN/SS1, RUN/SS2 (L2, E2): Run Control and Soft-Start
Pins. A voltage above 0.9V will turn on the module, and
below 0.6V will turn off the module. This pin has a 1M
resistor to V IN and a 1000pF capacitor to GND. The volt-
age on the RUN/SS pin clamps the control loop’s current
comparator threshold. A RUN/SS pin voltage of 2.375V
upon completion of soft-start guarantees the regulator can
deliver full output current. To turn off the module while
V IN remains active, the RUN/SS pin should be pulled low
with a falling edge ≤ 1μs to ensure the device does not
transition slowly through the internal undervoltage lockout
threshold. See Applications Information section for soft-
start information.
SW1, SW2 (H2-H6, B2-B6): The switching node of the
circuit is used for testing purposes. This can be connected
to copper on the board for improved thermal performance.
PGOOD
RUN/SS
R SS
1M
4.7μF
6.3V
V IN
V IN
22μF 2.375V TO 5.5V
6.3V
TRACK
SUPPLY
4.99k
C SSEXT
5.76k
C SS
1000pF
TRACK
COMP
INTERNAL
COMP
CONTROL, DRIVE
POWER FETS
M1
M2
0.47μH
C2
470pF
R1
4.99k
V OUT
4.7μF
6.3V
GND
100μF
X5R
V OUT
1.5V
4A
FB
R FB
5.76k
SW
4614 F01
Figure 1. Simplified LTM4614 Block Diagram of Each Switching Regulator Channel
4614fb
6
相关PDF资料
PDF描述
AT26DF161A-SU IC FLASH 16MBIT 70MHZ 8SOIC
ISL6614ACB IC DRIVER MOSF DUAL SYNC 14SOIC
MLG1005SR36J INDUCTOR MULTILAYER .36UH 0402
IFSC1008ABER2R2M01 INDUCTOR POWER 2.2UH 1.85A SMD
ECC18DRTI CONN EDGECARD 36POS DIP .100 SLD
相关代理商/技术参数
参数描述
DC1386B 功能描述:BOARD DEMO LTM8032 RoHS:否 类别:编程器,开发系统 >> 评估板 - DC/DC 与 AC/DC(离线)SMPS 系列:µModule® 标准包装:1 系列:- 主要目的:DC/DC,步降 输出及类型:1,非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND
DC1386B 制造商:Linear Technology 功能描述:DEMOBOARD NUMBER FOR LTM8032
DC1390-104K 制造商:API 制造商全称:API Delevan 功能描述:High Current Power Line Chokes
DC1390-105K 制造商:API 制造商全称:API Delevan 功能描述:High Current Power Line Chokes
DC1390-124K 制造商:API Delevan 功能描述:HIGH CURRENT POWER LINE CHOKE RADIAL LEADED POWER INDUCTOR, - Bulk