- 您现在的位置：买卖IC网 > PDF目录20401 > DC1385A (Linear Technology)BOARD EVAL LTM4614 PDF资料下载
参数资料
| 型号： | DC1385A |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL LTM4614 |
| 软件下载： | LTM4614 |
| 设计资源： | DC1385A Design Files DC1385A Schematic |
| 标准包装： | 1 |
| 系列： | µModule® |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.2V，1.8V |
| 电流 - 输出： | 4A，4A |
| 输入电压： | 2.375 ~ 5.5V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 1.25MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM4614 |
| 相关产品： | LTM4614IV#PBF-ND - IC UMODULE DC/DC DUAL 4A 144LGA LTM4614EV#PBF-ND - IC UMODULE DC/DC DUAL 4A 144LGA |
LTM4614
APPLICATIONS INFORMATION
V OUT
V IN
? D ? ( 1 – D )
I CIN(RMS) =
4.99k + R FB
V OUT = 0.8V ?
DualSwitchingRegulator
A typical LTM4614 application circuit is shown in Figure 12.
External component selection is primarily determined by
the maximum load current and output voltage. Refer to
Table 4 for specific external capacitor requirements for a
particular application.
V IN to V OUT Step-Down Ratios
There are restrictions in the maximum V IN and V OUT step-
down ratio than can be achieved for a given input voltage
on the two switching regulators. The LTM4614 is 100%
duty cycle capable, but the V IN to V OUT minimum dropout
will be a function the load current. A typical 0.5V minimum
is sufficient. See Typical Performance Characteristics.
Output Voltage Programming
Each regulator channel has an internal 0.8V reference
voltage. As shown in the Block Diagram, a 4.99k internal
feedback resistor connects the V OUT and FB pins together.
The output voltage will default to 0.8V with no externally
applied feedback resistor. Adding a resistor R FB from the
FB pin to GND programs the output voltage:
R FB
Table 1. FB Resistor Table vs Various Output Voltages
V OUT 0.8V 1.0V 1.2V 1.5V 1.8V 2.5V 3.3V
R FB Open 20k 10k 5.76k 3.92k 2.37k 1.62k
Input Capacitors
The LTM4614 module should be connected to a low AC
impedance DC source. One 4.7μF ceramic capacitor is
included inside the module for each regulator channel.
Additional input capacitors are needed if a large load step
is required up to the full 4A level and for RMS ripple cur-
rent requirements. A 47μF bulk capacitor can be used for
more input bulk capacitance. This 47μF capacitor is only
needed if the input source impedance is compromised by
long inductive leads or traces.
For a buck converter, the switching duty cycle can be
estimated as:
D =
Without considering the inductor current ripple, the RMS
current of the input capacitor can be estimated as:
I OUT(MAX)
η %
In the above equation, η % is the estimated efficiency of
the power module. The bulk capacitor can be a switcher-
rated aluminum electrolytic OS-CON or polymer capacitor.
If a low inductance plane is used to power the device,
then no input capacitance is required. The internal 4.7μF
ceramics on each channel input are typically rated for 1A
of RMS ripple current up to 85°C operation. The worst-
case ripple current for the 4A maximum current is 2A or
less. An additional 10μF or 22μF local ceramic capacitor
can be used to supplement the internal capacitor with an
additional 1A to 2A ripple current rating. See Figure 11
for recommended PCB layout.
Output Capacitors
The LTM4614 switchers are designed for low output volt-
age ripple on each channel. The bulk output capacitors
are chosen with low enough effective series resistance
(ESR) to meet the output voltage ripple and transient
requirements. The output capacitors can be low ESR tan-
talum capacitors, low ESR polymer capacitors or ceramic
capacitors. The typical output capacitance range is 66μF
to 100μF. Additional output filtering may be required by
the system designer if further reduction of output ripple
or dynamic transient spikes is required. Table 4 shows a
matrix of different output voltages and output capacitors
to minimize the voltage droop and overshoot during a 2A/
μs transient. The table optimizes total equivalent ESR and
total bulk capacitance to maximize transient performance.
See Figure 11 for recommended PCB layout.
4614fb
8
相关PDF资料 |
PDF描述 |
|---|---|
| AT26DF161A-SU | IC FLASH 16MBIT 70MHZ 8SOIC |
| ISL6614ACB | IC DRIVER MOSF DUAL SYNC 14SOIC |
| MLG1005SR36J | INDUCTOR MULTILAYER .36UH 0402 |
| IFSC1008ABER2R2M01 | INDUCTOR POWER 2.2UH 1.85A SMD |
| ECC18DRTI | CONN EDGECARD 36POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1386B | 功能描述:BOARD DEMO LTM8032 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:µModule® 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| DC1386B | 制造商:Linear Technology 功能描述:DEMOBOARD NUMBER FOR LTM8032 |
| DC1390-104K | 制造商:API 制造商全称:API Delevan 功能描述:High Current Power Line Chokes |
| DC1390-105K | 制造商:API 制造商全称:API Delevan 功能描述:High Current Power Line Chokes |
| DC1390-124K | 制造商:API Delevan 功能描述:HIGH CURRENT POWER LINE CHOKE RADIAL LEADED POWER INDUCTOR, - Bulk |
发布紧急采购，3分钟左右您将得到回复。