- 您现在的位置：买卖IC网 > PDF目录16617 > DC1496B-B (Linear Technology)BOARD EVAL LTC2942 PDF资料下载
参数资料
| 型号： | DC1496B-B |
| 厂商： | Linear Technology |
| 文件页数： | 10/18页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL LTC2942 |
| 软件下载： | QuikEval System |
| 设计资源： | DC1496B Design Files |
| 标准包装： | 1 |
| 系列： | QuikEval™ |
| 主要目的： | 电源管理，燃料量计 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LTC2942 |
| 主要属性： | I²C、SMBus 接口 |
| 次要属性： | LED 状态指示器 |
| 已供物品： | 板，线缆 |
| 相关产品： | DC590B-ND - BOARD DEMO USB SERIAL CONTROLLER LTC2942IDCB#TRMPBFDKR-ND - IC FUEL/GAS GAUGE LI-ION 6DFN LTC2942IDCB#TRMPBFCT-ND - IC FUEL/GAS GAUGE LI-ION 6DFN LTC2942IDCB-1#TRPBF-ND - IC FUEL/GAS GAUGE LI-ION 1A 6DFN LTC2942CDCB-1#TRPBF-ND - IC FUEL/GAS GAUGE LI-ION 1A 6DFN LTC2942IDCB-1#TRMPBFDKR-ND - IC FUEL/GAS GAUGE LI-ION 1A 6DFN LTC2942CDCB-1#TRMPBFDKR-ND - IC FUEL/GAS GAUGE LI-ION 1A 6DFN LTC2942IDCB-1#TRMPBFCT-ND - IC FUEL/GAS GAUGE LI-ION 1A 6DFN LTC2942CDCB-1#TRMPBFCT-ND - IC FUEL/GAS GAUGE LI-ION 1A 6DFN LTC2942IDCB-1#TRMPBFTR-ND - IC FUEL/GAS GAUGE LI-ION 1A 6DFN 更多... |
LTC2942
APPLICATIONS INFORMATION
R SENSE ≤
q LSB = 0.085mAh ?
50m ? M
q LSB = 0.085mAh ?
R SENSE ≤
0.085mAh ? 2 16
Alert/ChargeCompleteConfigurationB[2:1]
The AL /CC pin is a dual function pin configured by the
control register. By setting bits B[2:1] to [10] (default)
the AL /CC pin is configured as an alert pin following the
SMBus protocol. In this configuration the AL /CC pin is a
digital output and is pulled low if one of the three mea-
sured quantities (charge, voltage, temperature) exceeds
its high or low threshold or if the value of the accumulated
charge register overflows or underflows. An alert response
procedure started by the master resets the alert at the
AL /CC pin. For further information see the Alert Response
Protocol section.
Setting the control bits B[2:1] to [01] configures the AL /CC
pin as a digital input. In this mode, a high input on the
AL /CC pin communicates to the LTC2942 that the battery
is full and the accumulated charge register is set to its
maximum value FFFFh. The AL /CC pin would typically
be connected to the “charge complete” output from the
battery charger circuitry.
If neither the alert nor the charge complete functionality
is desired, bits B[2:1] should be set to [00]. The AL /CC
pin is then disabled and should be tied to GND.
Avoid setting B[2:1] to [11] as it enables the alert and the
charge complete modes simultaneously.
Choosing R SENSE
To achieve the specified precision of the coulomb counter,
the differential voltage between SENSE + and SENSE – must
stay within ±50mV. For differential input signals up to
±300mV the LTC2942 will remain functional but the preci-
sion of the coulomb counter is not guaranteed.
The required value of the external sense resistor, R SENSE ,
is determined by the maximum input range of V SENSE and
the maximum current of the application:
50mV
I MAX
The choice of the external sense resistor value influences
the gain of the coulomb counter. A larger sense resistor
gives a larger differential voltage between SENSE + and
SENSE – for the same current which results in more precise
coulomb counting. Thus the amount of charge represented
by the least significant bit (q LSB ) of the accumulated charge
(registers C, D) is equal to:
?
R SENSE 128
or
50m ?
R SENSE
when the prescaler is set to its default value of M = 128.
Note that 1mAh = 3.6C (coulomb).
Choosing R SENSE = 50mV/I MAX is not sufficient in ap-
plications where the battery capacity (Q BAT ) is very large
compared to the maximum current (I MAX ):
Q BAT > I MAX ? 5.5 Hours
For such low current applications with a large battery,
choosing R SENSE according to R SENSE = 50mV/I MAX can
lead to a q LSB smaller than Q BAT /2 16 and the 16-bit accu-
mulated charge register may underflow before the battery
is exhausted or overflow during charge. Choose, in this
case, a maximum R SENSE of:
? 50m ?
Q BAT
In an example application where the maximum current is
I MAX = 100mA, calculating R SENSE = 50mV/I MAX would
lead to a sense resistor of 500mΩ. This gives a q LSB of
8.5μAh and the accumulated charge register can represent
a maximum battery capacity of Q BAT = 8.5μAh ? 65535 =
557mAh. If the battery capacity is larger, R SENSE must be
lowered. For example, R SENSE must be reduced to 150mΩ
if a battery with a capacity of 1800mAh is used.
2942fa
10
相关PDF资料 |
PDF描述 |
|---|---|
| L-07C10NKV6T | CER INDUCTOR 10NH 0402 |
| HIP6503CBZ-T | IC ACPI MULTI POWER CTRLR 20SOIC |
| L-07C68NJV6T | CER INDUCTOR 68NH 0402 |
| ISL6443AIRZ-TK | IC CTRLR SGL/STP DWN PWM 28-QFN |
| RYM08DTKN-S288 | CONN EDGECARD 16POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1496B-B | 制造商:Linear Technology 功能描述:EVAL BOARD, LTC2942 BATTERY FUEL GAUGE |
| DC1496B-C | 制造商:Linear Technology 功能描述:BOARD EVAL FOR LTC2941-1 制造商:Linear Technology 功能描述:LTC2941-1 BATTERY GAS GAUGE 制造商:Linear Technology 功能描述:DEMO BOARD, LTC2941IDCB-1 BATTERY GAS GAUGE; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC2941; Kit Application Type:Power Management; Application Sub Type:Fuel Gauge; Kit Contents:Demo Board LTC2941 |
| DC1496B-D | 制造商:Linear Technology 功能描述:BOARD EVAL FOR LTC2942-1 制造商:Linear Technology 功能描述:LTC2942-1 BATTERY GAS GAUGE 制造商:Linear Technology 功能描述:DEMO BOARD, LTC2942IDCB-1 BATTERY GAS GAUGE; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC2942; Kit Application Type:Power Management; Application Sub Type:Fuel Gauge; Kit Contents:Demo Board LTC2942 |
| DC1498A | 功能描述:BOARD EVAL LTM4620 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:µModule® 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| DC15 | 制造商:Florida Misc. 功能描述: |
发布紧急采购，3分钟左右您将得到回复。