- 您现在的位置：买卖IC网 > PDF目录16687 > DC1621A (Linear Technology)BOARD DEMO LTM8062 PDF资料下载
参数资料
| 型号： | DC1621A |
| 厂商： | Linear Technology |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO LTM8062 |
| 设计资源： | DC1621A Design Files |
| 标准包装： | 1 |
| 系列： | LTM®, uModule® |
| 主要目的： | 电源管理，电池充电器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LTM8062 |
| 主要属性： | 2 芯锂离子电池 / 锂聚合物，7.2V 2A 输出 |
| 次要属性： | 9.75V ~ 32V 输入 |
| 已供物品： | 板 |
| 相关产品： | LTM8062EV#PBF-ND - IC BATTERY CHARGER TRACK 77-LGA LTM8062IV#PBF-ND - IC BATTERY CHARGER TRACK 77-LGA |
LTM8062/LTM8062A
PIN FUNCTIONS
V BAT(FLT) ? 2.5 ? 10 5
R1 = ( ? )
R1 ? 2.5 ? 10 5
R1 ? (2.5 ? 10 5 )
GND (Bank 1, Pin L7): Power and Signal Ground Return.
BAT (Bank 2): Battery Charge Current Output Bus. The
charge function operates to achieve the final float voltage
at this pin. The auto-restart feature initiates a new charging
cycle when the voltage at the ADJ pin falls 2.5% below
the float voltage. Once the charge cycle is terminated, the
input bias current of the BAT pin is reduced to minimize
battery discharge while the charger remains connected.
V INA (Bank 3): Anode of input reverse protection Schottky
diode. Connect the input power here if input reverse volt-
age protection is desired.
V IN (Bank 4): Charger Input Supply. Decouple with at least
4.7μF to GND. Connect the input power here if no input
reverse voltage protection is needed.
BIAS (Pin G7): The BIAS pin connects to the internal
power bus. In most cases connect to V BAT . If this is not
desirable, connect to a power source greater than 2.8V
and less than 10V.
CHRG (Pin K7): Open-Collector Charger Status Output;
typically pulled up through a resistor to a reference
voltage. This status pin can be pulled up to voltages as
high as V IN and can sink currents up to 10mA. During
a battery charging cycle, CHRG is pulled low. When the
charge current falls below C/10, the CHRG pin becomes
high impedance. If the internal timer is used for termina-
tion, the pin stays low during the charging cycle until the
charge current drops below a C/10 rate, approximately
200mA, even though the charger will continue to top off
the battery until the end-of-charge timer terminates the
charge cycle. A temperature fault also causes this pin to
be pulled low (see the Applications Information section).
NTC (Pin H6): Battery Temperature Monitor Pin. This pin
is the input to the NTC (negative temperature coefficient)
thermistor temperature monitoring circuit. This function is
enabled by connecting a 10kΩ, B = 3380 NTC thermistor
from the NTC pin to ground. The pin sources 50μA, and
monitors the voltage across the 10kΩ thermistor. When the
voltage on this pin is above 1.36V (T < 0°C) or below 0.29V
(T > 40°C), charging is disabled and the CHRG and FAULT
pins are both pulled low. If the internal timer termination is
being used, the timer is paused, suspending the charging
cycle. Charging resumes when the voltage on NTC returns
to within the 0.29V to 1.36V active region. There is approxi-
mately 5°C of temperature hysteresis associated with each
of the temperature thresholds. The temperature monitoring
function remains enabled while thermistor resistance to
ground is less than 250kΩ. If this function is not desired,
leave the NTC pin unconnected.
ADJ (Pin H7): Battery Float Voltage Feedback Input. The
charge function operates to achieve a final float voltage of
3.3V on this pin. The output battery float voltage (V BAT(FLT) )
is programmed using a resistor divider. V BAT(FLT) can be
programmed up to 14.4V. The auto-restart feature initi-
ates a new charging cycle when the voltage at the ADJ
pin falls 2.5% below the float voltage reference. The ADJ
pin input bias current is 110nA. Using a resistor divider
with an equivalent input resistance at the ADJ pin of 250k
compensates for input bias current error. Required resistor
values to program desired V BAT(FLT) follow the equations:
3.3
R2 = ( ? )
R1 is connected from BAT to ADJ, and R2 is connected
from ADJ to ground.
FAULT (Pin J7): Open-Collector Fault Status Output; typi-
cally pulled up through a resistor to a reference voltage.
This status pin can be pulled up to voltages as high as
V IN and can sink currents up to 10mA. This pin indicates
charge cycle fault conditions during a battery charging
cycle. A temperature fault causes this pin to be pulled
low. If the internal timer is used for termination, a bad bat-
tery fault also causes this pin to be pulled low. If no fault
conditions exist, the FAULT pin remains high impedance
(see the Applications Information section).
TMR (Pin J6): End-Of-Cycle Timer Programming Pin.
If a timer-based charge termination is desired, connect
a capacitor from this pin to ground. Full charge end-of
cycle time (in hours) is programmed with this capacitor
following the equation:
t EOC = C TIMER ? 4.4 ? 10 6
A bad battery fault is generated if the battery does not
reach the precondition threshold voltage within one-eighth
of t EOC , or:
t PRE = C TIMER ? 5.5 ? 10 5
8062fd
For more information www.linear.com/LTM8062
7
相关PDF资料 |
PDF描述 |
|---|---|
| ELC-06D180E | COIL CHOKE 18UH RADIAL |
| ECC28DCMD-S288 | CONN EDGECARD 56POS .100 EXTEND |
| H6MMS-2436G | DIP CABLE - HDM24S/AE24G/HDM24S |
| M1DXA-1636J | IDC CABLE - MKR16A/MC16G/X |
| V110C5T75BF | CONVERTER MOD DC/DC 5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1621G | 制造商:Aleph America Corporation 功能描述: |
| DC1623A | 功能描述:BOARD EVAL LTM8003 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:µModule® 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| DC1625A-A | 功能描述:BOARD DEMO FOR LTC4227-1 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| DC1625A-B | 功能描述:BOARD DEMO FOR LTC4227-2 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| DC1627 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
发布紧急采购，3分钟左右您将得到回复。