- 您现在的位置：买卖IC网 > PDF目录17032 > DC1783A-E (Linear Technology)BOARD SAR ADC LTC2379-18 PDF资料下载
参数资料
| 型号： | DC1783A-E |
| 厂商： | Linear Technology |
| 文件页数： | 6/26页 |
| 文件大小： | 0K |
| 描述： | BOARD SAR ADC LTC2379-18 |
| 软件下载： | QuikEval II System |
| 设计资源： | DC1783A Design Files DC1783A Schematic |
| 标准包装： | 1 |
| 系列： | QuikEval™ |
| ADC 的数量： | 1 |
| 位数： | 18 |
| 采样率（每秒）： | 1.6M |
| 数据接口： | 串行，SPI? |
| 输入范围： | ±VREF |
| 在以下条件下的电源（标准）： | 18mW @ 1.6MSPS |
| 工作温度： | 0°C ~ 70°C |
| 已用 IC / 零件： | LTC2379-18 |
| 已供物品： | 板 |
| 相关产品： | DC1216A-A-ND - BOARD EVAL 100MHZ CLOCK DC718C-ND - DEMO QUIKEVAL-II DATA LTC2379IMS-18#TRPBF-ND - IC ADC 18BIT SPI/SRL 16MSOP LTC2379IDE-18#TRPBF-ND - IC ADC 18BIT SPI/SRL 16DFN LTC2379HMS-18#PBF-ND - IC ADC 18BIT SPI/SRL 16MSOP LTC2379CMS-18#PBF-ND - IC ADC 18BIT SPI/SRL 16MSOP LTC2379HMS-18#TRPBF-ND - IC ADC 18BIT SPI/SRL 16MSOP LTC2379CMS-18#TRPBF-ND - IC ADC 18BIT SPI/SRL 16MSOP LTC2379CDE-18#TRPBF-ND - IC ADC 18BIT SPI/SRL 16DFN LTC2379CDE-18#PBF-ND - IC ADC 18BIT SPI/SRL 16DFN 更多... |
LTC2379-18
14
237918fa
Figure 11. 32k Point FFT with fIN = 2kHz of the LTC2379-18
FREQUENCY (kHz)
0
100 200 300 400
800
700
600
500
–180
AMPLITUDE
(dBFS)
–60
–40
–20
–80
–100
–120
–140
–160
0
237918 F11
SNR = 101.2dB
THD = –120dB
SINAD = 101.1dB
SFDR = 121dB
APPLICATIONS INFORMATION
0μA to a maximum of 1.3mA at 1.6Msps. This step in DC
current draw triggers a transient response in the reference
that must be considered since any deviation in the refer-
ence output voltage will affect the accuracy of the output
code. In applications where the transient response of the
reference is important, the fast settling LTC6655-5 refer-
ence is also recommended.
DYNAMIC PERFORMANCE
Fast Fourier Transform (FFT) techniques are used to test
the ADC’s frequency response, distortion and noise at the
rated throughput. By applying a low distortion sine wave
and analyzing the digital output using an FFT algorithm,
the ADC’s spectral content can be examined for frequen-
cies outside the fundamental. The LTC2379-18 provides
guaranteed tested limits for both AC distortion and noise
measurements.
Signal-to-Noise and Distortion Ratio (SINAD)
The signal-to-noise and distortion ratio (SINAD) is the
ratio between the RMS amplitude of the fundamental input
frequency and the RMS amplitude of all other frequency
components at the A/D output. The output is band-limited
to frequencies from above DC and below half the sampling
frequency. Figure 11 shows that the LTC2379-18 achieves
a typical SINAD of 101dB at a 1.6MHz sampling rate with
a 2kHz input.
Signal-to-Noise Ratio (SNR)
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC. Figure 11 shows
that the LTC2379-18 achieves a typical SNR of 101.2dB
at a 1.6MHz sampling rate with a 2kHz input.
Total Harmonic Distortion (THD)
Total Harmonic Distortion (THD) is the ratio of the RMS sum
of all harmonics of the input signal to the fundamental itself.
The out-of-band harmonics alias into the frequency band
between DC and half the sampling frequency (fSMPL/2).
THD is expressed as:
THD
=20log
V2
2 + V32 + V42 +…+ V
N
2
V1
where V1 is the RMS amplitude of the fundamental fre-
quency and V2 through VN aretheamplitudesofthesecond
through Nth harmonics.
POWER CONSIDERATIONS
The LTC2379-18 provides two power supply pins: the
2.5V power supply (VDD), and the digital input/output
interface power supply (OVDD). The flexible OVDD supply
allows the LTC2379-18 to communicate with any digital
logic operating between 1.8V and 5V, including 2.5V and
3.3V systems.
Power Supply Sequencing
The LTC2379-18 does not have any specific power supply
sequencing requirements. Care should be taken to adhere
to the maximum voltage relationships described in the
Absolute Maximum Ratings section. The LTC2379-18
has a power-on-reset (POR) circuit that will reset the
LTC2379-18 at initial power-up or whenever the power
supply voltage drops below 1V. Once the supply voltage
re-enters the nominal supply voltage range, the POR will
相关PDF资料 |
PDF描述 |
|---|---|
| STD17W-S | WIRE & CABLE MARKERS |
| STD17W-Q | WIRE & CABLE MARKERS |
| DC1278A | BOARD SAR ADC LTC2351-14 |
| STD17W-B | WIRE & CABLE MARKERS |
| DC1082A-F | BOARD SAR ADC LTC2355-14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1783A-F | 功能描述:BOARD SAR ADC LTC2378-18 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1783A-G | 功能描述:BOARD SAR ADC LTC2377-18 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1783A-H | 功能描述:BOARD SAR ADC LTC2376-18 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1785A | 功能描述:BOARD DEMO LTC2991 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:QuikEval™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| DC1785A | 制造商:Linear Technology 功能描述:EVAL BOARD, LTC2991 TEMP, VOLTAGE, CURRE |
发布紧急采购，3分钟左右您将得到回复。