- 您现在的位置：买卖IC网 > PDF目录16542 > DC1786A (Linear Technology)BOARD DEMO LTC2871 PDF资料下载
参数资料
| 型号： | DC1786A |
| 厂商： | Linear Technology |
| 文件页数： | 2/36页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO LTC2871 |
| 设计资源： | DC1786A Design Files DC1786A Schematic |
| 标准包装： | 1 |
| 主要目的： | 接口，收发器，RS-232/RS-485 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LTC2871 |
| 主要属性： | 3 个驱动器，3 个接收器 |
| 次要属性： | 3 V ~ 5.5 V 电源 |
| 已供物品： | 板 |
| 相关产品： | LTC2871CUHF#PBF-ND - IC TXRX RS485/RS422 38-QFN LTC2871IUHF#PBF-ND - IC TXRX RS485/RS422 38-QFN LTC2871CFE#PBF-ND - IC TXRX RS485/RS422 38-TSSOP LTC2871IFE#PBF-ND - IC TXRX RS485/RS422 38-TSSOP LTC2871CUHF#TRPBF-ND - IC TXRX RS485/RS422 38-QFN LTC2871IFE#TRPBF-ND - IC TXRX RS485/RS422 38-TSSOP LTC2871IUHF#TRPBF-ND - IC TXRX RS485/RS422 38-QFN LTC2871CFE#TRPBF-ND - IC TXRX RS485/RS422 38-TSSOP |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC2870/LTC2871
10
28701f
PIN FUNCTIONS
PIN NAME
LTC2870
QFN
LTC2870
TSSOP
LTC2871
QFN
LTC2871
TSSOP
DESCRIPTION
DOUT1
23
27
RS232 Driver Output 1.
DOUT2
22
26
RS232 Driver Output 2.
DI
7
11
RS485 Driver Input.
DY
7
10
RS485 Driver Input or RS232 Driver Input 1.
DZ
8
11
RS232 Driver Input 2.
Y
19
22
26
30
RS485 Positive Driver Output. RS232 Driver Output 1 (LTC2870).
RS485 Positive Receiver Input (LTC2870 or LTC2871 in Half-Duplex Mode).
Z
17
20
24
28
RS485 Negative Driver Output or RS232 Driver Output 2 (LTC2870).
RS485 Negative Receiver Input (LTC2870 or LTC2871 in Half-Duplex Mode).
485/232
4
7
Interface Select Input. A logic low enables RS232 mode and a high enables RS485 mode.
The mode determines which transceiver inputs and outputs are accessible at the LTC2870
pins as well as which is controlled by the driver and receiver enable pins.
RXEN
5
8
Receiver Enable. A logic high disables RS232 and RS485 receivers leaving receiver
outputs Hi-Z. A logic low enables the RS232 or RS485 receivers, depending on the state
of the interface select input 485/232 .
DXEN
6
9
Driver Enable. A logic low disables the RS232 and RS485 drivers leaving the driver output
in a Hi-Z state. A logic high enables the RS232 or RS485 drivers, depending on the state
of the interface select input 485/232.
RX232
11
15
RS232 Receiver Enable. A logic high disables the RS232 receivers and input termination
resistors leaving the RS232 receiver outputs in a Hi-Z state. A logic low enables the
RS232 receivers and resistors, subject to the state of the CH2 pin.
RX485
5
9
RS485 Receiver Enable. A logic high disables the RS485 receiver leaving the RS485
receiver output in a Hi-Z state. A logic low enables the RS485 receiver and resistors,
subject to the state of the CH2 pin.
DX232
10
14
RS232 Driver Enable. A logic low disables the RS232 drivers leaving the RS232 driver
outputs in a Hi-Z state. A logic high enables the RS232 drivers.
DX485
6
10
RS485 Driver Enable. A logic low disables the RS485 driver leaving the RS485 driver
output in a Hi-Z state. A logic high enables the RS485 driver.
H/F
27
2
37
3
RS485 Half-Duplex Select Input. A logic low is used for full-duplex operation where pins
A and B are the receiver inputs and pins Y and Z are the driver outputs. A logic high is
used for half-duplex operation where pins Y and Z are both the receiver inputs and driver
outputs and pins A and B do not serve as the receiver inputs. The impedance on A and B
and state of differential termination between A and B is independent of the state of H/F.
The H/F pin has no effect on RS232 operation.
TE485
28
3
38
4
RS485 Termination Enable. A logic high enables a 120Ω resistor between pins A and
B and also between pins Y and Z. A logic low opens the resistors, leaving A/B and Y/Z
unterminated. The LTC2870 termination resistors are never enabled in RS232 mode.
FEN
9
12
13
17
Fast Enable. A logic high enables fast enable mode. In fast enable mode the integrated
DC/DC converter is active independent of the state of driver, receiver, and termination
enable pins allowing faster circuit enable times than are otherwise possible. A logic low
disables fast enable mode leaving the state of the DC/DC converter dependent on the state
of driver, receiver, and termination enable control inputs. The DC/DC converter powers
down only when FEN is low and all drivers, receivers, and terminators are disabled (refer
to Table 1).
LB
26
1
36
2
Loopback Enable. A logic high enables logic loopback diagnostic mode, internally routing
the driver input logic levels to the receiver output pins. This applies to both RS232
channels as well as the RS485 driver/receiver. The targeted receiver must be enabled for
the loopback signal to be available on its output. A logic low disables loopback mode. In
Loopback mode, signals are not inverted from driver inputs to receiver outputs.
CH2
4
8
RS232 Channel 2 Disable. A logic high disables RS232 receiver 2 and RS232 driver 2
independent of the state of RX232 and DX232 pins. In this state, the disabled driver
output becomes Hi-Z and the 5kΩ load resistor on the disabled receiver input is opened.
A logic low allows both RS232 transceiver channels to be enabled or disabled together
based on the RX232 and DX232 pins.
相关PDF资料 |
PDF描述 |
|---|---|
| GCM24DCCS-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| 6278016-3 | CABLE ASSY SC-SC DUPLEX MM 3M |
| 5503995-2 | CABLE ASSEM FIBER ST-ST 2 METER |
| ECO-S1HA152BA | CAP ALUM 1500UF 50V 20% SNAP |
| EEU-FR1J821 | CAP ALUM 820UF 63V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1788A-B | 制造商:Linear Technology 功能描述:EVAL BOARD, LT4275B POE & PD CONTROLLER, Silicon Manufacturer:Linear Technology, |
| DC1788A-C | 制造商:Linear Technology 功能描述:EVAL BOARD, LT4275C POE & PD CONTROLLER, Silicon Manufacturer:Linear Technology, |
| DC1788B-A | 制造商:Linear Technology 功能描述:EVAL BOARD FOR LT4275 90W 制造商:Linear Technology 功能描述:LT4275 POWERED DEVICE CTRL EVAL BOARD 制造商:Linear Technology 功能描述:DEMO BOARD, LT4275, POWER OVER ETHERNET CONTROLLER, Silicon Manufacturer:Linear |
| DC178A | 功能描述:BOARD SAR ADC LTC1418 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1792 | 功能描述:BOARD DAC LTC2756 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:QuikEval™, SoftSpan™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。