- 您现在的位置：买卖IC网 > PDF目录17063 > DC845A (Linear Technology)BOARD DELTA SIGMA ADC LTC2448 PDF资料下载
参数资料
| 型号： | DC845A |
| 厂商： | Linear Technology |
| 文件页数： | 3/28页 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2448 |
| 软件下载： | QuikEval System |
| 设计资源： | DC845A Design File DC845A Schematic |
| 标准包装： | 1 |
| 系列： | QuikEval™ |
| ADC 的数量： | 1 |
| 位数： | 24 |
| 采样率（每秒）： | 8k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2448 |
| 已供物品： | 板 |
| 相关产品： | LTC2448IUHF#PBF-ND - IC ADC 24BIT HI SPEED 38QFN LTC2448CUHF#PBF-ND - IC ADC 24BIT HI SPEED 38QFN LTC2448IUHF#TRPBF-ND - IC ADC 24BIT HI SPEED 38QFN LTC2448CUHF#TRPBF-ND - IC ADC 24BIT HI SPEED 38QFN LTC2448CUHF-ND - IC ADC 24BIT HI SPEED 38QFN LTC2448IUHF-ND - IC ADC 24BIT HI SPEED 38QFN LTC2448CUHF#TR-ND - IC ADC 24BIT HI SPEED 38QFN LTC2448IUHF#TR-ND - IC ADC 24BIT HI SPEED 38QFN |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2444/LTC2445/
LTC2448/LTC2449
11
2444589fb
external SCK mode is selected by tying EXT (Pin 3) LOW
for external SCK and HIGH for internal SCK.
Serial Data Output (SDO)
The serial data output pin, SDO (Pin 37), provides the
result of the last conversion as a serial bit stream (MSB
first) during the data output state. In addition, the SDO pin
is used as an end of conversion indicator during the
conversion and sleep states.
When CS (Pin 36) is HIGH, the SDO driver is switched to
a high impedance state. This allows sharing the serial
interface with other devices. If CS is LOW during the
convert or sleep state, SDO will output EOC. If CS is LOW
during the conversion phase, the EOC bit appears HIGH on
the SDO pin. Once the conversion is complete, EOC goes
LOW. The device remains in the sleep state until the first
rising edge of SCK occurs while CS = LOW.
Chip Select Input (CS)
The active LOW chip select, CS (Pin 36), is used to test the
conversion status and to enable the data output transfer as
described in the previous sections.
In addition, the CS signal can be used to trigger a new
conversion cycle before the entire serial data transfer has
been completed. The LTC2444/LTC2445/LTC2448/
LTC2449 will abort any serial data transfer in progress and
start a new conversion cycle anytime a LOW-to-HIGH
transition is detected at the CS pin after the converter has
entered the data output state.
Serial Data Input (SDI)
The serial data input (SDI, Pin 34) is used to select the
speed/resolution and input channel of the LTC2444/
LTC2445/LTC2448/LTC2449. SDI is programmed by a
serial input data stream under the control of SCK during
the data output cycle, see Figure 3.
Initially, after powering up, the device performs a conver-
sion with IN+ = CH0, IN– = CH1, OSR = 256 (output rate
nominally 880Hz), and 1X speedup mode (no Latency).
Once this first conversion is complete, the device enters
the sleep state and is ready to output the conversion result
and receive the serial data input stream programming the
speed/resolution and input channel for the next conver-
sion. At the conclusion of each conversion cycle, the
device enters this state.
In order to change the speed/resolution or input channel,
the first 3 bits shifted into the device are 101. This is
compatible with the programming sequence of the
LTC2414/LTC2418. If the sequence is set to 000 or 100,
the following input data is ignored (don’t care) and the
previously selected speed/resolution and channel remain
valid for the next conversion. Combinations other than
101, 100, and 000 of the 3 control bits should be avoided.
If the first 3 bits shifted into the device are 101, then the
following 5 bits select the input channel for the following
conversion (see Tables 3 and 4). The next 5 bits select the
speed/resolution and mode 1X (no Latency) 2X (double
output rate with one conversion latency), see Table 5. If
these 5 bits are set to all 0’s, the previous speed remains
selected for the next conversion. This is useful in applica-
tions requiring a fixed output rate/resolution but need to
change the input channel. In this case, the timing and input
sequence is compatible with the LTC2414/LTC2418.
When an update operation is initiated (the first 3 bits are
101) the first 5 bits are the channel address. The first
bit, SGL, determines if the input selection is differential
(SGL = 0) or single-ended (SGL = 1). For SGL = 0, two
adjacent channels can be selected to form a differential
input. For SGL = 1, one of 8 channels (LTC2444/LTC2445)
or one of 16 channels (LTC2448/LTC2449) is selected as
the positive input. The negative input is COM for all single
ended operations. The remaining 4 bits (ODD, A2, A1, A0)
determine which channel is selected. The LTC2448/
LTC2449 use all 4 bits to select one of 16 different input
channels (see table 3) while in the case of the LTC2444/
LTC2445, A2 is always 0, and the remaining 3 bits select
one of 8 different input channels (see Table 4).
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490277 | CABLE JUMPER 1.25MM .030M 22POS |
| RBM08DCBS-S189 | CONN EDGECARD 16POS R/A .156 SLD |
| 0210391080 | CABLE JUMPER 1MM .102M 37POS |
| DC682A | BOARD SAR ADC LTC1859 |
| EBM12DTBT-S189 | CONN EDGECARD 24POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC846A | 功能描述:BOARD DELTA SIGMA ADC LTC2447 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC847A | 功能描述:BOARD DELTA SIGMA ADC LTC2446 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC850 | 制造商:Molex 功能描述: |
| DC852A | 功能描述:BOARD DEMO FOR LTC4354 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| DC8550 | 制造商:DCCOM 制造商全称:Dc Components 功能描述:TECHNICAL SPECIFICATIONS OF PNP EPITAXIAL PLANAR TRANSISTOR |
发布紧急采购，3分钟左右您将得到回复。