- 您现在的位置：买卖IC网 > PDF目录17061 > DC951A (Linear Technology)BOARD DELTA SIGMA ADC LTC2481 PDF资料下载
参数资料
| 型号： | DC951A |
| 厂商： | Linear Technology |
| 文件页数： | 14/40页 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2481 |
| 软件下载： | QuikEval System |
| 设计资源： | DC951A Design File DC951A Schematic |
| 标准包装： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 7.5 |
| 数据接口： | I²C，串行，SPI? |
| 工作温度： | 0°C ~ 70°C |
| 已用 IC / 零件： | LTC2481 |
| 已供物品： | 板 |
| 相关产品： | LTC2481HDD#TRPBF-ND - IC ADC DELTA SIGMA 16BIT 10DFN LTC2481HDD#PBF-ND - IC ADC 16BIT I2C 7.5SPS 10DFN LTC2481CDD#TRPBF-ND - IC ADC 16BIT I2C 10-DFN LTC2481IDD#TRPBF-ND - IC ADC 16BIT I2C 10-DFN LTC2481IDD#PBF-ND - IC ADC 16BIT I2C 10-DFN LTC2481CDD#PBF-ND - IC ADC 16BIT I2C 10-DFN |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC2481
21
2481fc
APPLICATIONS INFORMATION
conversion result following POR is accurate within the
specications of the device if the power supply voltage is
restored within the operating range (2.7V to 5.5V) before
the end of the POR time interval.
On-Chip Temperature Sensor
The LTC2481 contains an on-chip PTAT (proportional to
absolute temperature) signal that can be used as a tempera-
ture sensor. The internal PTAT has a typical value of 420mV
at 27°C and is proportional to the absolute temperature
value with a temperature coefcient of 420/(27 + 273) =
1.40mV/°C (SLOPE), as shown in Figure 11. The internal
PTAT signal is used in a single-ended mode referenced to
device ground internally. The GAIN is automatically set to
one (independent of the values of GS0, GS1, GS2) in order
to preserve the PTAT property at the ADC output code
and avoid an out of range error. The 1x speed mode with
automatic offset calibration is automatically selected for
the internal PTAT signal measurement as well.
When using the internal temperature sensor, if the output
code is normalized to RSDA = VPTAT/VREF, the temperature
is calculated using the following formula:
TK =
RSDA VREF
SLOPE
in Kelvin
and
TC =
RSDA VREF
SLOPE
– 273 in
° C
where SLOPE is nominally 1.4mV/°C.
Since the PTAT signal can have an initial value variation
which results in errors in SLOPE, to achieve absolute
temperature measurements, a one-time calibration is
needed to adjust the SLOPE value. The converter output of
the PTAT signal, R0SDA,ismeasuredataknowntemperature
T0 (in °C) and the SLOPE is calculated as:
SLOPE
=
R0SDA VREF
T0
+ 273
This calibrated SLOPE can be used to calculate the tem-
perature.
If the same VREF source is used during calibration and
temperature measurement, the actual value of the VREF
is not needed to measure the temperature as shown in
the calculation below:
TC =
RSDA VREF
SLOPE
– 273
=
RSDA
R0SDA
T0
+ 273
(
)–273
Reference Voltage Range
The LTC2481 external reference voltage range is 0.1V
to VCC. The converter output noise is determined by
the thermal noise of the front-end circuits, and as such,
its value in nanovolts is nearly constant with reference
voltage. Since the transition noise (600nV) is much less
than the quantization noise (VREF/217), a decrease in the
reference voltage will increase the converter resolution. A
reduced reference voltage will also improve the converter
performance when operated with an external conversion
clock (external fO signal) at substantially higher output
data rates (see the Output Data Rate section). VREF must
be ≥1.1V to use the internal temperature sensor.
The reference input is differential. The differential reference
input range (VREF = REF+ – REF–) is 100mV to VCC and the
common mode reference input range is 0V to VCC.
Figure 11. Internal PTAT Signal vs Temperature
TEMPERATURE (°C)
–60
V
PTAT
(mV)
500
600
120
2481 F11
400
200
30
090
–30
60
300
VCC = 5V
IM = 1
SLOPE = 1.40mV/°C
相关PDF资料 |
PDF描述 |
|---|---|
| EBC28DCAI | CONN EDGECARD 56POS R/A .100 SLD |
| LGU2C561MELB | CAP ALUM 560UF 160V 20% SNAP |
| DC873A | BOARD SAR ADC LTC1867L |
| DEMO9S08SH32 | DEMO BOARD FOR MC9S08SH32 |
| ASC07DRTS | CONN EDGECARD 14POS .100 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC955A | 功能描述:BOARD DELTA SIGMA ADC LTC2483 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:Easy Drive™, QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC956A | 功能描述:BOARD DELTA SIGMA ADC LTC2485 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:Easy Drive™, QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC959A | 制造商:Linear Technology 功能描述:BOARD DEMO LTC4257-1 制造商:Linear Technology 功能描述:EVAL BOARD, LTC4257CDD-1 POE |
| DC95F103V | 功能描述:热敏电阻 - NTC 10KOhms +-.1C Epoxy Coated RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| DC95F103VN | 制造商:GE Sensing & Inspection Technologies 功能描述:Thermistor;10;PCB Mount Mtg. Type;1.5In Lead;Bare Tinned Copper 制造商:GE Measurement & Control 功能描述:+/-.1oC (0oC - 70oC) Interchangeable Chip |
发布紧急采购，3分钟左右您将得到回复。