- 您现在的位置：买卖IC网 > PDF目录11283 > DEHR33F821KB3B (Murata Electronics North America)CAP CER 820PF 3.15KV 10% RADIAL PDF资料下载
参数资料
| 型号： | DEHR33F821KB3B |
| 厂商： | Murata Electronics North America |
| 文件页数： | 23/84页 |
| 文件大小： | 0K |
| 描述： | CAP CER 820PF 3.15KV 10% RADIAL |
| 标准包装： | 3,000 |
| 系列： | DEH |
| 电容： | 820pF |
| 电压 - 额定： | 3150V（3.15kV） |
| 容差： | ±10% |
| 温度系数： | R |
| 安装类型： | 通孔 |
| 工作温度： | -25°C ~ 125°C |
| 应用： | 通用 |
| 封装/外壳： | 径向 - 圆盘形 |
| 尺寸/尺寸： | 0.472" 直径（12.00mm） |
| 高度 - 座高（最大）： | 0.591"（15.00mm） |
| 引线间隔： | 0.295"（7.50mm） |
| 特点： | 高电压，低耗散因子 |
| 包装： | 散装 |
| 引线型： | 直形 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
! Note ? Please read rating and ! CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
? This catalog has only typical speci?cations. Therefore, please approve our product speci?cations or transact the approval sheet for product speci?cations before ordering.
C85E.pdf
Apr.7,2014
DEJ Series Speci?cations and Test Methods
Continued from the preceding page.
No.
Item
Specifications
Test Method
Appearance
I.R.
No marked defect
1000M Ω min.
As shown in the figure, the lead
wires should be immersed in
solder of 350±10°C up to 1.5 to
Thermal
Screen
Capacitor
1.5
2.0mm from the root of terminal for
to 2.0mm
Soldering
10 Effect
3.5±0.5 sec.
Pre-treatment:
Molten
Solder
(Non-Preheat)
Dielectric
Strength
Per Item 6
Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition* 1 for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 4 to 24 hrs. at room
condition.* 1
Appearance
I.R.
No marked defect
1000M Ω min.
First the capacitor should be
stored at 120+0/-5°C for
60+0/-5 sec.
Thermal
Screen
Capacitor
1.5
Then, as in the figure, the lead
to 2.0mm
wires should be immersed in
solder of 260+0/-5°C up to 1.5 to
Soldering
11 Effect
(On-Preheat)
Dielectric
Strength
Per Item 6
Molten
Solder
2.0mm from the root of terminal
for 7.5+0/-1 sec.
Pre-treatment:
Capacitor should be stored at 85±2°C for 1 hr., then placed at
5
room condition* 1 for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 4 to 24 hrs. at
room condition.* 1
Appearance
Capacitance
No marked defect
Within the specified tolerance
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
12
Vibration
Resistance
D.F.
Char.
E
F
Specifications
D.F. V 2.5%
D.F. V 5.0%
total amplitude, with about a 1-minute rate of vibration change
from 10Hz to 55Hz and back to 10Hz.
Apply for a total of 6 hrs., 2 hrs. each in 3 mutually perpendicular
directions.
13
Solvent
Resistance
Appearance
No marked defect
The capacitor should be immersed into a isopropyl alcohol for
30±5 sec.
Appearance
No marked defect
14
Humidity
(Under
Steady
State)
Capacitance
Change
D.F.
Char.
E
F
Char.
E
F
Capacitance Change
Within ±20%
Within ±30%
Specifications
D.F. V 5.0%
D.F. V 7.5%
Set the capacitor for 500±12 hrs. at 40±2°C in 90 to 95%
relative humidity.
Pre-treatment:
Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition* 1 for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition.* 1
I.R.
Dielectric
Strength
Appearance
1000M Ω min.
Per Item 6
No marked defect
Capacitance
Change
Char.
E
F
Capacitance Change
Within ±20%
Within ±30%
The capacitor should be subjected to 40±2°C, relative humidity
of 90 to 98% for 8 hrs., and then removed in room temperature
for 16 hrs. until 5 cycles are completed.
15
Humidity
Insulation
D.F.
Char.
E
F
Specifications
D.F. V 5.0%
D.F. V 7.5%
Pre-treatment:
Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition* 1 for 24±2 hrs. before initial measurements.
Post-treatment:
I.R.
Dielectric
Strength
1000M Ω min.
Per Item 6
Capacitor should be stored for 1 to 2 hrs. at room condition.* 1
* 1 "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued on the following page.
21
相关PDF资料 |
PDF描述 |
|---|---|
| GRM3196R2A391JZ01D | CAP CER 390PF 100V 5% R2H 1206 |
| GRM3196R2A361JZ01D | CAP CER 360PF 100V 5% R2H 1206 |
| GRM3196P2A391JZ01D | CAP CER 390PF 100V 5% P2H 1206 |
| GRM3196P2A361JZ01D | CAP CER 360PF 100V 5% P2H 1206 |
| GRM3197U1H332JZ01D | CAP CER 3300PF 50V 5% U2J 1206 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DEHR33F821KN3A | 功能描述:瓷片电容器 820pF 3150 Volts 10% RoHS:否 制造商:Vishay/Cera-Mite 电容:0.01 uF 容差:20 % 电压额定值:3 kV 工作温度范围:- 25 C to + 105 C 损耗因数 DF: 端接类型:Radial 产品:High Voltage Ceramic Disc Capacitors |
| DEI05L | 制造商:Electrolube 功能描述:DEIONISED WATER, 5L |
| DEI1270A-MES | 制造商:DEI 功能描述: |
| DEIC420 | 制造商:IXYS Corporation 功能描述:MOSFET DRVR 20A 1-OUT Lo Side Non-Inv 28-Pin SOIC 制造商:IXYS Corporation 功能描述:IC DRIVER MOSFET DE275 制造商:IXYS Corporation 功能描述:IC, DRIVER, MOSFET DE275 |
| DEIC421 | 功能描述:RF MOSFET DRIVER 20 AMP RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
发布紧急采购，3分钟左右您将得到回复。