- 您现在的位置：买卖IC网 > PDF目录11270 > DG643DY-T1-E3 (Vishay Siliconix)IC VIDEO SWITCH SPDT 16SOIC PDF资料下载
参数资料
| 型号： | DG643DY-T1-E3 |
| 厂商： | Vishay Siliconix |
| 文件页数： | 7/18页 |
| 文件大小： | 0K |
| 描述： | IC VIDEO SWITCH SPDT 16SOIC |
| 标准包装： | 2,500 |
| 功能： | 视频开关 |
| 电路： | 2 x SPDT |
| 导通状态电阻： | 15 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 10 V ~ 18 V，±10 V ~ 15 V |
| 电流 - 电源： | 3.5mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 带卷 (TR) |
VISHAY SILICONIX
TrenchFET Power MOSFETs
Application Note 808
Mounting LITTLE FOOT, SO-8 Power MOSFETs
APPLICATION
NOTE
Document Number: 70740
www.vishay.com
Revision: 18-Jun-07
1
Wharton McDaniel
Surface-mounted LITTLE FOOT power MOSFETs use
integrated circuit and small-signal packages which have
been been modified to provide the heat transfer capabilities
required by power devices. Leadframe materials and
design, molding compounds, and die attach materials have
been changed, while the footprint of the packages remains
the same.
See Application Note 826, Recommended Minimum Pad
Patterns With Outline Drawing Access for Vishay Siliconix
MOSFETs, (http://www.vishay.com/ppg?72286), for the
basis of the pad design for a LITTLE FOOT SO-8 power
MOSFET. In converting this recommended minimum pad
to the pad set for a power MOSFET, designers must make
two connections: an electrical connection and a thermal
connection, to draw heat away from the package.
In the case of the SO-8 package, the thermal connections
are very simple. Pins 5, 6, 7, and 8 are the drain of the
MOSFET for a single MOSFET package and are connected
together. In a dual package, pins 5 and 6 are one drain, and
pins 7 and 8 are the other drain. For a small-signal device or
integrated circuit, typical connections would be made with
traces that are 0.020 inches wide. Since the drain pins serve
the additional function of providing the thermal connection
to the package, this level of connection is inadequate. The
total cross section of the copper may be adequate to carry
the current required for the application, but it presents a
large thermal impedance. Also, heat spreads in a circular
fashion from the heat source. In this case the drain pins are
the heat sources when looking at heat spread on the PC
board.
Figure 1. Single MOSFET SO-8 Pad
Pattern With Copper Spreading
Figure 2. Dual MOSFET SO-8 Pad Pattern
With Copper Spreading
The
minimum
recommended
pad
patterns
for
the
single-MOSFET SO-8 with copper spreading (Figure 1) and
dual-MOSFET SO-8 with copper spreading (Figure 2) show
the starting point for utilizing the board area available for the
heat-spreading copper. To create this pattern, a plane of
copper overlies the drain pins. The copper plane connects
the drain pins electrically, but more importantly provides
planar copper to draw heat from the drain leads and start the
process of spreading the heat so it can be dissipated into the
ambient air. These patterns use all the available area
underneath the body for this purpose.
Since surface-mounted packages are small, and reflow
soldering is the most common way in which these are
affixed to the PC board, “thermal” connections from the
planar copper to the pads have not been used. Even if
additional planar copper area is used, there should be no
problems in the soldering process. The actual solder
connections are defined by the solder mask openings. By
combining the basic footprint with the copper plane on the
drain pins, the solder mask generation occurs automatically.
A final item to keep in mind is the width of the power traces.
The absolute minimum power trace width must be
determined by the amount of current it has to carry. For
thermal reasons, this minimum width should be at least
0.020 inches. The use of wide traces connected to the drain
plane provides a low impedance path for heat to move away
from the device.
0.027
0.69
0.078
1.98
0.2
5.07
0.196
5.0
0.288
7.3
0.050
1.27
0.027
0.69
0.078
1.98
0.2
5.07
0.088
2.25
0.288
7.3
0.050
1.27
0.088
2.25
相关PDF资料 |
PDF描述 |
|---|---|
| VI-253-IY-S | CONVERTER MOD DC/DC 24V 50W |
| GRM31CR61C226KE15K | CAP CER 22UF 16V 10% X5R 1206 |
| VE-2VN-IX-F2 | CONVERTER MOD DC/DC 18.5V 75W |
| GRM3197U1H472JZ01D | CAP CER 4700PF 50V 5% U2J 1206 |
| DSPIC30F6011AT-30I/PF | IC DSPIC MCU/DSP 132K 64TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DG646BH | 制造商:未知厂家 制造商全称:未知厂家 功能描述:GTO Thyristors - Disc / Puk Devices |
| DG646BH25 | 制造商:Dynex Semiconductor 功能描述:GTO THYRISTOR |
| DG646BH25_05 | 制造商:DYNEX 制造商全称:Dynex Semiconductor 功能描述:Gate Turn-off Thyristor |
| DG646BH25-125A | 制造商:Dynex Semiconductor 功能描述:GTO THYRISTOR |
| DG646BH25-148 | 制造商:Dynex Semiconductor 功能描述:SCR - PHASE CONTROL THYRISTOR |
发布紧急采购，3分钟左右您将得到回复。