参数资料
| 型号： | DLP-USB232M-G |
| 厂商： | DLP Design Inc |
| 文件页数： | 5/12页 |
| 文件大小： | 0K |
| 描述： | MODULE USB-TO-TTL SRL UART CONV |
| 产品目录绘图： | DLP-USBxxxM-G |
| 标准包装： | 1 |
| 系列： | DLP-USB232M |
| 类型： | USB 至 UART |
| 连接器类型： | 迷你型 B 至 DIL（双直插式） |
| 产品目录页面： | 635 (CN2011-ZH PDF) |
| 其它名称： | 813-1018 |
DLP-USB232M User ’s Manual
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VCC-IO (In) 3.0 volt to +5.25 volt VCC to the UART interface pins 10..12, 14..16 and 18..25.
When interfacing with 3.3v external logic connect VCC-IO to the 3.3v supply of the external logic,
otherwise connect to VCC to drive out at 5v CMOS level. This pin must be connected to VCC from
the target electronics or EXTVCC.
EXTVCC – (In) Use for applying main power (4.4 to 5.25 Volts) to the module. Connect to
PORTVCC if module is to be powered by the USB port (typical configuration)
PORTVCC - (Out) Power from USB port. Connect to EXTVCC if module is to be powered by the
USB port (typical configuration). 500mA maximum current available to USB adapter and target
electronics if USB device is configured for high power.
TXLED# - (O.C.) LED Drive - Pulses Low when Transmitting Data via USB
PWRCTL (IN) Bus Powered – Tie Low / Self Powered – Tie High
POWEREN# (OUT) Goes Low after the device is configured via USB, then high during USB
suspend. Can be used to control power to external logic using a P-Channel Logic Level
MOSFET switch. Enable the Interface Pull-Down Option in EEPROM when using the PWREN# pin
in this way.
TXDEN (OUT) Enable Transmit Data for RS485
RI # (IN) Ring Indicator Control Input. When the Remote Wakeup option is enabled in the
EEPROM, taking RI# low can be used to resume the PC USB Host controller from suspend.
DCD# (IN)Data Carrier Detect Control Input
DSR# (IN)Data Set Ready Control Input / Handshake signal
DTR# (OUT)Data Terminal Ready Control Output / Handshake signal
CTS# (IN) Clear To Send Control Input / Handshake signal
RTS# (OUT) Request To Send Control Output / Handshake signal
RXD (IN) Receive Asynchronous Data Input
TXD (OUT)Transmit Asynchronous Data Output
Copyright ? DLP Design 2002
Page 5 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| DLP-USB232R | MODULE USB-TO-SRL UART 18-DIP |
| DLP-USB245M-G | MODULE USB-TO-TTL PARL FIFO CONV |
| DLP-USB245R | MODULE USB-TO-PARL FIFO 18-DIP |
| DM163001 | BOARD DEMO PICDEM-1 |
| DM163004-LT | BOARD DEMO PICDEM.NET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DLP-USB232M-G2 | 功能描述:MODULE USB-TO-TTL SRL UART CONV 制造商:dlp design inc. 系列:- 零件状态:在售 类型:USB 至串行 转换自（适配器端）:USB - B 2.0 母头 转换至（适配器端）:DIL（Dual Inline） 接口:UART 特性:- 包括:- 标准包装:1 |
| DLP-USB232R | 功能描述:界面模块 USB-TO-SERIAL UART INTERFACE MODULE RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度: |
| DLP-USB245M | 功能描述:界面模块 USB-FIFO Adapter RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度: |
| DLP-USB245M-G | 功能描述:界面模块 USB-FIFO Adapter RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度: |
| DLP-USB245R | 功能描述:界面模块 USB-TO-PARALLEL FIFO INTERFACE MODULE RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。