参数资料
| 型号： | DLP-USB245M-G |
| 厂商： | DLP Design Inc |
| 文件页数： | 5/15页 |
| 文件大小： | 0K |
| 描述： | MODULE USB-TO-TTL PARL FIFO CONV |
| 产品目录绘图： | DLP-USBxxxM-G |
| 标准包装： | 1 |
| 系列： | DLP-USB245M |
| 类型： | USB 至 FIFO |
| 连接器类型： | USB-B 至 DIL（双直插式） |
| 产品目录页面： | 635 (CN2011-ZH PDF) |
| 其它名称： | 813-1019 |
DLP-USB245M User Manual
in step one. Windows will then complete the installation of the device drivers for the DLP-USB245M board. The
next time the DLP-USB245M module is attached, the host PC will immediately load the correct drivers without any
prompting. Reboot the PC if prompted to do so.
5. Run the serializer program and write the VID (0403), PID (6001), a description string of your choosing and
manufacturers ID as instructed in the instruction manual that was downloaded with the serializer software.
Terminate the serializer program and disconnect the DLP-USB245M board from the USB cable. Wait 10 seconds
and reconnect the DLP-USB245M board. Reboot the PC if instructed to do so.
NOTE 1 - The DLP-USB245M comes pre-programmed with a default VID and PID. Step 5 is optional and only
required if different VID/PID codes are required.
NOTE 2 – The “Test” button on the serializer program is intended for use with the DLP-USB232M module (and
FT232BM device) and will fail if used with the DLP-USB245M module. The “Read” function will work and will
present the contents of the EEPROM as well as the serial number and description strings stored in the EEPROM.
At this point the DLP-USB245M is ready for use. Note that the DLP-USB245M will appear non-responsive if data sent
from the host PC is not read from the FT245BM device by an attached microcontroller/microprocessor/DSP/FPGA/
etc…
Copyright ? DLP Design 2002
Page 5 of 15
相关PDF资料 |
PDF描述 |
|---|---|
| DLP-USB245R | MODULE USB-TO-PARL FIFO 18-DIP |
| DM163001 | BOARD DEMO PICDEM-1 |
| DM163004-LT | BOARD DEMO PICDEM.NET |
| DM163005 | KIT EVAL PIC16C432/433 LIN BUSS |
| DM163007 | PICDEM CAN-LIN 1 FOR 18C658/858 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DLP-USB245R | 功能描述:界面模块 USB-TO-PARALLEL FIFO INTERFACE MODULE RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度: |
| DLP-UT1 | 功能描述:工业温度传感器 TEMPERATURE SENSOR RoHS:否 制造商:Texas Instruments 准确性:1 C 功能:Temperature Sensing 25 摄氏度时的电阻: 温度范围:- 55 C to + 127 C 电源电流: 电源电压:2.7 V to 5.5 V |
| DLP-UTH8 | 功能描述:数据记录与采集 DLP SENSOR HUB RoHS:否 制造商:Lantronix 描述/功能:Analog device server 显示器类型:None 电流额定值: |
| DLPVA-100-F | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Low Frequency Voltage Amplifier |
| DLPVA-100-F-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Low Frequency Voltage Amplifier |
发布紧急采购，3分钟左右您将得到回复。