- 您现在的位置：买卖IC网 > PDF目录21901 > DMS-40PC-1-RS-C (Murata Power Solutions Inc)DPM LED 2VDC 4.5DIGIT RED PDF资料下载
参数资料
| 型号： | DMS-40PC-1-RS-C |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 5/6页 |
| 文件大小： | 0K |
| 描述： | DPM LED 2VDC 4.5DIGIT RED |
| 产品目录绘图： | Digital Panel Meter |
| 3D 型号： | DMS-40PC Series.pdf DMS-40PC Series.sldprt DMS-40PC Series.stp DMS-40PC Series.igs |
| 标准包装： | 12 |
| 系列： | DMS-40PC |
| 类型： | 伏特表 |
| 测量范围： | ±2V |
| 显示器样式： | 红色字符，黑色背景 |
| 显示器类型： | LED |
| 显示器正面尺寸： | 2.09" L x 0.84" W（53.1 x 21.3mm） |
| 显示器位数： | 4.5 |
| 显示器位数 - 高度： | 0.520"（13.21mm） |
| 背光： | 无 |
| 安装类型： | 面板安装 |
| 端子： | PC 引脚 |
| 电源电压： | 4.75 ~ 5.25V |
| 产品目录页面： | 2855 (CN2011-ZH PDF) |
| 其它名称： | 811-1046 |
DMS-40PC Series
4? Digit, LED Display Digital Panel Voltmeters
APPLICATIONS
5. Engineering Scaling and Input Attenuation : In many applications,
the input signal must be scaled, or divided down, before being applied
to the DMS-40PC. In some situations, the input signal exceeds the
full-scale range of the meter, and in other applications, a direct
one-to-one relation does not exist between the input voltage and
the desired display reading. For an example of the second situation,
assume an input voltage of 1.0Vdc is required to display a reading of
“7500” when applied to a ±2V input meter. An input divider circuit,
constructed with two series resistors with an output-to-input ratio of
0.75, will scale the 1.0V signal down to 0.75V.
Engineering scaling and input attenuation are discussed in Ap Note 4
of the DATEL Digital Panel Voltmeter Catalog. Compensating for inputs
which have a zero offset is also discussed.
6. BCD Outputs (DMS-40PC-X-RS and -RL-BCD Models Only) :
Models with a “-BCD” suf?x have 12 extra output pins, labeled
A through L (6 per side), that provide the following information: mul-
tiplexed serial BCD data, digit drive, and polarity indication. The data
present on pins A - L simultaneously drives the meter’s internal LED
display. All functions on pins A - L are 5V CMOS compatible, however,
they are only rated to drive one, 74LS series, TTL load. CMOS logic
IC’s, for example 74HC or 74HCT series devices, should be used when
more fan-out capability is required.
As the timing diagram in Figure 5 indicates, 100Hz is the optimum
display scan rate when the BCD outputs are used to drive external
LED displays. Faster scan rates, while permissible, are not necessary.
Slower scanning, however, may result in noticeable “?ickering” of
the display. Common anode LED’s, combined with a 74LS247 BCD
to seven-segment decoder, is the simplest way of implementing an
external display. A seventy-?ve to one-hundred Ohm resistor on each
LS247 segment-drive output provides adequate display brightness.
The functions of pins A - L are listed below:
BCD DATA (pins I - L) : Four lines are used for BCD (Binary Coded
Decimal) data outputs, representing the numbers 0 - 9. Positive-logic
convention (a high represents a “1”) is used.
DIGIT DRIVE ( pins A - E) : These ?ve outputs, when gated with STROBE,
can be used to direct the BCD DATA into external latches. DIGIT DRIVE
outputs may also be connected directly to the bases of NPN transistors
in remote-display con?gurations. The digits are scanned right-to-left, i.e.,
MSD (DIGIT 1 DRIVE) to LSD (DIGIT 5 DRIVE).
BUSY (pin G) : This is a status pin that goes high at the start of an ana-
log-to-digital (A/D) conversion cycle and remains high until the conver-
sion ends.
STROBE (pin H) : A string of ?ve sequential, active-low, STROBE pulses
are output (after BUSY goes low) indicating the end of a conversion and
the availability of new data. The 5 STROBE pulses occur only once per
conversion, or 2.5 times each second. STROBE can be used to latch the
BCD data (on pins I - L) into external latches. Either edge can be used
since STROBE (~ 5μsec wide) is active only in the center of the cor-
responding DIGIT DRIVE and BCD DATA outputs.
POLARITY (pin F) : This pin, which is also used inside the DMS-40PC to
drive the negative-sign segment, indicates whether the last input signal
conversion was positive (POLARITY set high) or negative (POLARITY set
low). POLARITY, unlike BCD DATA, is not multiplexed. For data latching
purposes, POLARITY should be sampled during the STROBE pulse for
digit 1 (most signi?cant digit).
Approx. 8msec
DIGIT DRIVE 1
(MSD)
Approx. 2msec
Approx. 2msec
DIGIT DRIVE 2
DIGIT DRIVE 3
DIGIT DRIVE 4
DIGIT DRIVE 5
(LSD)
BUSY
Approx. 5μsec
STROBE OUT
BCD DATA
(4 LINES)
Data from
Previous Conversion
5 Strobes Only Per Conversion
1
2
3
4
5
1
2
3
4
5
MSD
LSD
Figure 6. BCD Data Timing Diagram
www.murata-ps.com/support
09/27/11
MPM_DMS-40PC.C06 Page 5 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| DK631 | DPM LED 2V RED DIP |
| DK102 | LCD DPM +9V 2V 3.5 DIGIT |
| DMS-30PC-1-GS-C | DPM LED MINI 2VDC 3.5DIGIT GRN |
| DMS-20PC-1-DCM-C | DPM LED 8-50VDC 3.5DIGIT RED |
| 2N7000RLRAG | MOSFET N-CH 60V 200MA TO-92 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DMS-40PC-1-YS | 功能描述:数字面板表 4.5 Digit +-2V Input Std Yellow RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM |
| DMS-40PC-1-YS-C | 功能描述:数字面板表 4.5 Digit +-2V Input Std Yellow RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM |
| DMS-40PC-2 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:4 1/2Digit, LED Display Precision, Miniature Digital Panel Voltmeters |
| DMS-40PC-2-GS | 功能描述:数字面板表 4.5 Digit+-20V Input StdGreen RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM |
| DMS-40PC-2-GS-C | 功能描述:数字面板表 4.5 Digit+-20V Input StdGreen RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM |
发布紧急采购，3分钟左右您将得到回复。