- 您现在的位置：买卖IC网 > PDF目录17306 > DP83848C-POE-EK (National Semiconductor)BOARD EVALUATION DP83848C PDF资料下载
参数资料
| 型号： | DP83848C-POE-EK |
| 厂商： | National Semiconductor |
| 文件页数： | 4/86页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION DP83848C |
| 标准包装： | 1 |
| 系列： | PowerWise® |
| 主要目的： | 特殊用途 DC/DC，以太网供电（POE） |
| 输出及类型： | 1，隔离 |
| 功率 - 输出： | 24W |
| 输出电压： | 3.3V |
| 电流 - 输出： | 7.3A |
| 输入电压： | 39 ~ 57V |
| 稳压器拓扑结构： | 回扫 |
| 频率 - 开关： | 250kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LM5072 |
| 相关产品： | DP83848CVVX/NOPBTR-ND - TXRX ETHERNET PHYTER 48-LQFP DP83848CVV-ND - IC TXRX ETHERNET PHYTER 48-LQFP |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页
11
www.national.com
DP
83
84
8
C
1.3 Clock Interface
1.4 LED Interface
See Table 3 for LED Mode Selection.
Signal Name
Type
Pin #
Description
X1
I
34
CRYSTAL/OSCILLATOR INPUT: This pin is the primary clock
reference input for the DP83848C and must be connected to a 25
MHz 0.005% (+50 ppm) clock source. The DP83848C supports
either an external crystal resonator connected across pins X1 and
X2, or an external CMOS-level oscillator source connected to pin
X1 only.
RMII REFERENCE CLOCK: This pin is the primary clock refer-
ence input for the RMII mode and must be connected to a 50 MHz
0.005% (+50 ppm) CMOS-level oscillator source.
X2
O
33
CRYSTAL OUTPUT: This pin is the primary clock reference out-
put to connect to an external 25 MHz crystal resonator device.
This pin must be left unconnected if an external CMOS oscillator
clock source is used.
25MHz_OUT
O
25
25 MHz CLOCK OUTPUT:
In MII mode, this pin provides a 25 MHz clock output to the sys-
tem.
In RMII mode, this pin provides a 50 MHz clock output to the sys-
tem.
This allows other devices to use the reference clock from the
DP83848C without requiring additional clock sources.
Signal Name
Type
Pin #
Description
LED_LINK
S, O, PU
28
LINK LED: In Mode 1, this pin indicates the status of the LINK.
The LED will be ON when Link is good.
LINK/ACT LED: In Mode 2 and Mode 3, this pin indicates transmit
and receive activity in addition to the status of the Link. The LED
will be ON when Link is good. It will blink when the transmitter or
receiver is active.
LED_SPEED
S, O, PU
27
SPEED LED: The LED is ON when device is in 100 Mb/s and OFF
when in 10 Mb/s. Functionality of this LED is independent of mode
selected.
LED_ACT/COL
S, O, PU
26
ACTIVITY LED: In Mode 1, this pin is the Activity LED which is
ON when activity is present on either Transmit or Receive.
COLLISION/DUPLEX LED: In Mode 2, this pin by default indi-
cates Collision detection. For Mode 3, this LED output may be
programmed to indicate Full-duplex status instead of Collision.
相关PDF资料 |
PDF描述 |
|---|---|
| 695D335X9050F2T | CAP TANT 3.3UF 50V 10% 2414 |
| ISL62881CCPUEVAL2Z | EVAL BOARD ISL62881CCPU 28QFN |
| MDC3105LT1 | IC RELAY/DRVR INDUCT LOAD SOT23 |
| LM4040D30ILPRE3 | IC VREF SHUNT PREC 3V TO-92-3 |
| ASPI-0602S-820M-T | INDUCTOR POWER 82UH 0602 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DP83848CVV | 制造商:Texas Instruments 功能描述:IC, 10/100 ETHERNET PHY, SMD, LQFP48 |
| DP83848CVV/NOPB | 功能描述:以太网 IC PHYTER COMMERCIAL TEMP SGL PORT RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| DP83848CVV/NOPB | 制造商:Texas Instruments 功能描述:Ethernet Transceiver |
| DP83848CVVX | 制造商:Texas Instruments 功能描述:PHY 1-CH 10Mbps/100Mbps 48-Pin LQFP T/R |
| DP83848CVVX/NOPB | 功能描述:以太网 IC PHYTER COMMERCIAL TEMP SGL PORT RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。