- 您现在的位置：买卖IC网 > Datasheet目录409 > DR7003-DK (RFM)3G DEVELOPMENT KIT 303.825 MHZ Datasheet资料下载
参数资料
| 型号： | DR7003-DK |
| 厂商： | RFM |
| 文件页数： | 5/7页 |
| 文件大小： | 0K |
| 描述： | 3G DEVELOPMENT KIT 303.825 MHZ |
| 标准包装： | 1 |
| 类型： | 收发器 |
| 频率： | 303.825MHz |
| 适用于相关产品： | DR7003 |
| 已供物品： | 2 个板，2 根天线，线缆，CD |
| 其它名称： | 583-1047 |
Theory of Operation
The DR7003 evaluation module is centered around the TR7003
ASH Transceiver. The DR7003 may operate in backward
compatible 2G mode, or in the enhanced 3G mode. Since 3G mode
requires the use of a serial I/O port to configure internal registers,
the module includes an on-board Silicon Labs C8051F330
microcontroller to control access to the serial port. When 2G mode
is enabled the microcontroller serves no function. When 3G mode
is enabled the microcontroller constantly scans pins 8-15 for a
change of logic state. When a state change is detected on one or
more of these pins, the microcontroller automatically updates the
internal configuration registers via the serial port of the TR7003.
The microcontroller assumes full control of the CFG pin, CFGCLK
pin, and CFGDAT pin in 3G mode to continuously update the
internal registers.
The DR7003 module is designed to demonstrate the performance
of the TR7003 ASH Transceiver at 4.8kbps, although other data
rates are possible with changes in on-board component values.
Current Consumption Monitor (J5)
The current consumption of the TR7003 device may be monitored
by removing J5 and connecting an ammeter across the terminals.
When J5 is removed it isolates the TR7003 from VCC powering the
on-board processor to give a true reading of the current
consumption of only the TR7003 without the additional current
usage of the processor. J5 must be installed to power the TR7003
if not using the header for current measurement.
Power-up Mode Select (J2)
J2 is used to select the operating mode of the TR7003 device only
at power-up. The state of J2 when VCC is applied will determine
whether the board operates in 2G mode or 3G mode. Pin 2 (center
pin) of J2 is connected to Pin 19 (CFG) of the TR7003 device and
is grounded for 2G mode and functions as the chip select line for the
serial interface in 3G mode. Installing the jumper will either connect
the CFG pin of the TR7003 to GND or directly to the processor for
control in 3G mode. See the table below for power-up jumper
settings.
See pin descriptions and refer to the TR7003 datasheet.
The DR7003 module may be mounted on a prototype assembly
using standard 0.1” spacing, 10-pin headers spaced 0.9” apart.
2G Mode Operation
Setting
J2(1-2)
J2(2-3)
Power-up Mode
2G
3G
Pin 19
Connected to GND
Connected to Processor
The DR7003 may operate in 2G mode. See pin 15 description and
Power-up Mode Select (J2) section for mode select details. In 2G
mode, the CFGCLK pin (18) and CFGDAT pin (17) operate as
CTRL0 and CTRL1, respectively, just as for second-generation
devices. The CFGCLK and CFGDAT pins are a high impedance
input allowing external control for 2G configuration. The logic levels
on CFGCLK (CTRL0) and CFGDAT (CTRL1) control the default 2G
operation as shown below:
After power-up if 3G mode is selected, pin 15 (3G Sel) must be
pulled ‘High’ to initiate the processor to operate in 3G mode. Failure
to pull pin 15 ‘High’ after power-up will cause the processor to
remain inactive.
CFGCLK (CNTRL0)
0
1
CFGDAT (CNTRL1)
0
0
MODE
SLEEP
TX OOK
0
1
1
1
TX ASK
RX
J4
J5 Header
J2 Header
Programming Header (J4)
The programming header allows for custom firmware development
for the Silicon Labs C8051F330 if desired. Contact RFM for more
information about custom firmware development.
www.RFM.com E-mail: info@rfm.com
?2008 by RF Monolithics, Inc.
Page 5 of 7
DR7003 - 4/8/08
相关PDF资料 |
PDF描述 |
|---|---|
| DR8000-DK | 3G DEVELOPMENT KIT 916MHZ |
| DR8001-DK | 3G DEVELOPMENT KIT 868.35MHZ |
| DR8100-DK | 3G DEVELOPMENT KIT 916MHZ |
| DS1720S/T&R | IC THERMOMETER/STAT DIG 8-SOIC |
| DS1820 | IC DGTL THERMOMETER TO92-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DR7003-EV | 功能描述:射频开发工具 3G Transceiver Eval Module 303.825 MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| DR703PBKV | 制造商:Pass & Seymour/Legrand 功能描述:700W DECOR ROTARY W/PILOT LGT BK |
| DR7110 | 功能描述:固态继电器-工业安装 4-32 VDC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DR7111 | 功能描述:固态继电器-工业安装 90-250 VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DR73-100 | 制造商:Cooper Bussmann Electronics 功能描述: 制造商:COOPER BUSSMANN 功能描述:Ind Power Shielded Wirewound 10uH 20% 100KHz Ferrite 2.08A T/R 制造商:COOPER BUSSMANN 功能描述:Inductor Power Shielded Wirewound 10uH 20% 100KHz Ferrite 2.08A 65.6mOhm DCR T/R |
发布紧急采购，3分钟左右您将得到回复。