- 您现在的位置：买卖IC网 > PDF目录1993 > DS1052Z-100+ (Maxim Integrated Products)IC PROG PWM 5BIT 100KHZ 8-SOIC PDF资料下载
参数资料
| 型号： | DS1052Z-100+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/14页 |
| 文件大小： | 0K |
| 描述： | IC PROG PWM 5BIT 100KHZ 8-SOIC |
| 标准包装： | 100 |
| 类型： | 脉宽调制器（PWM） |
| PLL： | 无 |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:1 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 100kHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | * |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | * |
| 包装： | 管件 |
DS1052
4 of 14
The master device generates all serial clock pulses and the START and STOP conditions. A transfer is
ended with a STOP condition or with a repeated START condition. Since a repeated START condition is
also the beginning of the next serial transfer, the bus will not be released.
The DS1052 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL, respectively. After
each byte is received, an acknowledge bit is transmitted. START and STOP conditions are recognized
as the beginning and end of a serial transfer. Address recognition is performed by hardware after
reception of the slave (device) address and direction bit.
2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode.
However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data
is transmitted on SDA by the DS1052 while the serial clock is input on SCL. START and STOP
conditions are recognized as the beginning and end of a serial transfer.
SLAVE ADDRESS
A command/control byte is the first byte received following the START condition from the master
device. The command/control byte consists of a four-bit control code. For the DS1052, this is set as 0101
binary for read/write operations. The next three bits of the command/control byte are the device select
bits or slave address (A2, A1, A0). They are used by the master device to select which of eight possible
devices is to be accessed. When reading or writing the DS1052, the device select bits must match the
device select pins (A2, A1, A0). The last bit of the command/control byte (R/W) defines the operation to
be performed. When set to a one a read operation is selected, and when set to a zero a write operation is
selected. The command control byte is presented in Figure 3.
Following the START condition, the DS1052 monitors the SDA bus checking the device type identifier
being transmitted. Upon receiving the 0101 control code, the appropriate device address bits, and the
read/write bit, the slave device outputs an “acknowledge” signal on the SDA line.
COMMAND AND PROTOCOL
The command and protocol structure of the DS1052 allows the user to read or write the PWM
configuration register or place the device in a low-current state (shut-down mode) and recall the device
from a low-current state. Additionally, the 2-wire command/protocol structure of the DS1052 will support
eight different devices that can be uniquely controlled.
Figure 4a, b, c, d, & e show the five different command and protocol bytes for the DS1052. These include
the following command operations: 1) Set PWM duty cycle, 2) Set PWM duty cycle 100%, 3) Set
shutdown mode, 4) Set recall mode, 5) Read PWM configuration register.
The command operation “Set PWM Duty Cycle” is used to configure the output duty cycle of the device.
The DS1052 has a 5-bit resolution and is capable of setting the duty cycle output from 0% up to 96.88%
in steps of 3.125%. A binary value of (00000B) sets the duty cycle output at 0% while a binary value of
(11111B) sets the duty cycle output at 96.88%.
The command operation “Set PWM Duty Cycle 100%” is used to configure the output duty cycle of the
device to a “full-on.” This command is provided in addition to the Set PWM Duty Cycle command for
flexibility and convenience in total duty cycle coverage. It allows the user to provide a total duty cycle
range from 0% to 100%.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1077LZ-40 | IC ECONOSCILLATOR 40MHZ 8-SOIC |
| DS1077U-120+ | IC ECONOSCILLATOR 120MHZ 8-USOP |
| DS1081LE+ | IC CLOCK MOD SS 8-TSSOP |
| DS1083LR-U+ | IC CLOCK MOD SS 3.3V TSOT23-6 |
| DS1100LZ-75+W | IC DELAY LINE 5TAP 75NS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1052Z-100+ | 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| DS10-56B | 制造商:TRANSMISSION DEVELOPMENTS 功能描述:MOULDED SPUR GEAR 1.0, 56 |
| DS-105-C | 制造商:Power Dynamics Inc 功能描述: |
| DS-105TR | 制造商:OPTICOMM 制造商全称:OPTICOMM 功能描述:10BaseT Ethernet Transceiver |
| DS106 | 制造商:Cooper Hand Tools / Weller 功能描述: |
发布紧急采购，3分钟左右您将得到回复。