- 您现在的位置：买卖IC网 > PDF目录97857 > DS1077U-133 (DALLAS SEMICONDUCTOR) 133.333 MHz, OTHER CLOCK GENERATOR, PDSO8 PDF资料下载
参数资料
| 型号： | DS1077U-133 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Clock Generator |
| 英文描述： | 133.333 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| 封装： | 0.118 INCH, MICRO, SO-8 |
| 文件页数： | 5/17页 |
| 文件大小： | 103K |
| 代理商： | DS1077U-133 |
DS1077
13 of 17
COMMAND SET
Data and control information is read from and written to theDS1077 in the format shown in Figure 3 To
write to the DS1077, the master will issue the slave address of the DS1077 and the R/W bit will be set to 0.
After receiving an acknowledge, the bus master provides a command protocol. After receiving this protocol,
the DS1077 will issue an acknowledge, and then the master may send data to the DS1077. If the DS1077 is
to be read, the master must send the command protocol as before, and then issue a repeat START condition
and then the control byte again, this time with the R/W bit set to 1 to allow reading of the data from the
DS1077.
The command set for the DS1077 is as follows:
Access DIV [01]
If R/W is 0, this command writes to the DIV register. After issuing this command, the next data byte value
is to be written into the DIV register.
If R/W* is 1, the next data byte read is the value stored in the DIV register.
Access MUX [02]
If R/W is 0, this command writes to the MUX register. After issuing this command, the next data byte
value is to be written into the MUX register.
If R/W* is 1, the next data byte read is the value stored in the MUX register.
Access BUS [0D]
If R/W is 0, this command writes to the BUS register. After issuing this command, the next data byte value
is to be written into the BUS register.
If R/W* is 1, the next data byte read is the value stored in the BUS register.
Write E2 [3F]
If WC=0 the EEPROM is automatically written to at the end of each command, this is a DEFAULT
condition. In this case the command “WRITE E2” is not needed
If WC=1, the EEPROM is only written when the “WRITE E2” command is issued. On receipt of the
“WRITE E2” command the contents of the DIV and MUX registers are written into the EEPROM, thus
locking in the register settings.
EXCEPTION: The Bus register is always automatically written to EEPROM after a write,
regardless of the value of WC
相关PDF资料 |
PDF描述 |
|---|---|
| DS1077Z-120 | 120 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| DS1077Z-66 | 66.666 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| DS1077Z-125 | 125 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| DS1077Z-100 | 100 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| DS1100U-175/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1077U-133/T&R | 功能描述:可编程振荡器 RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1077U-133+ | 功能描述:可编程振荡器 EconOscillator/Dvdr 133MHz 150mil 2-Wire RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1077U-133+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:ECONO-OSC 8P USOP 2-W 133MHZ T&R LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC ECONOSCILLATOR 133.3MHZ 8USOP 制造商:Maxim Integrated Products 功能描述:Programmable Oscillators EconOscillator/Dvdr 133MHz 150mil 2-Wire |
| DS1077U-133+T&R | 功能描述:可编程振荡器 EconOscillator/Dvdr 133MHz 150mil 2-Wire RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1077U-66 | 功能描述:可编程振荡器 EconOscillator/Dvdr 66MHz 150mil 2-Wire RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
发布紧急采购，3分钟左右您将得到回复。