- 您现在的位置：买卖IC网 > PDF目录97859 > DS1284 (MAXIM INTEGRATED PRODUCTS INC) 1 TIMER(S), REAL TIME CLOCK, PDIP28 PDF资料下载
参数资料
| 型号： | DS1284 |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Timer or RTC |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PDIP28 |
| 封装： | 0.600 INCH, PLASTIC, DIP-28 |
| 文件页数： | 15/18页 |
| 文件大小： | 299K |
| 代理商： | DS1284 |
DS1284/DS1286
6 of 18
TIME-OF-DAY REGISTERS
Registers 0, 1, 2, 4, 6, 8, 9, and A contain time-of-day data in BCD. Ten bits within these eight registers
are not used and always read 0 regardless of how they are written. Bits 6 and 7 in the months register (9)
are binary bits. When set to logic 0,
EOSC (bit 7) enables the RTC oscillator. This bit is set to logic 1 as
shipped from Dallas Semiconductor to prevent lithium energy consumption during storage and shipment.
The user normally turns this bit on during device initialization. However, the oscillator can be turned on
and off as necessary by setting this bit to the appropriate level. Bit 6 of this same byte controls the square-
wave output (pin 23). When set to logic 0, the square-wave output pin outputs a 1024Hz square-wave
signal. When set to logic 1, the square-wave output pin is in a high-impedance state. Bit 6 of the hours
register is defined as the 12- or 24-hour select bit. When set to logic 1, the 12-hour format is selected. In
the 12-hour format, bit 5 is the AM/PM bit with logic 1 being PM. In the 24-hour mode, bit 5 is the
second 10-hour bit (20–23 hours). The time-of-day registers are updated every 0.01 seconds from the
RTC, except when the TE bit (bit 7 of register B) is set low or the clock oscillator is not running. The
preferred method of synchronizing data access to and from the watchdog timekeeper is to access the
command register by doing a write cycle to address location 0B and setting the TE (transfer enable) bit to
a logic 0. Doing so freezes the external time-of-day registers at the present recorded time, allowing access
to occur without danger of simultaneous update. When the watch registers have been read or written, a
second write cycle to location 0B, setting the TE bit to a logic 1, puts the time-of-day registers back to
being updated every 0.01 second. No time is lost in the RTC because the internal copy of the time-of-day
register buffers is continually incremented while the external memory registers are frozen.
An alternate method of reading and writing the time-of-day registers is to ignore synchronization.
However, any single read may give erroneous data as the RTC may be in the process of updating the
external memory registers as data is being read. The internal copies of seconds through years are
incremented and time-of-day alarm is checked during the period that hundreds of seconds read 99 and are
transferred to the external register when hundredths of seconds roll from 99 to 00. A way of making sure
data is valid is to do multiple reads and compare. Writing the registers can also produce erroneous results
for the same reasons. A way of making sure that the write cycle has caused proper update is to do read
verifies and re-execute the write cycle if data is not correct. While the possibility of erroneous results
from reads and write cycles has been stated, it is worth noting that the probability of an incorrect result is
kept to a minimum due to the redundant structure of the watchdog timekeeper.
TIME-OF-DAY ALARM REGISTERS
Registers 3, 5, and 7 contain the time-of-day alarm registers. Bits 3, 4, 5, and 6 of register 7 always read 0
regardless of how they are written. Bit 7 of registers 3, 5, and 7 are mask bits (Figure 3). When all the
mask bits are logic 0, a time-of-day alarm only occurs when registers 2, 4, and 6 match the values stored
in registers 3, 5, and 7. An alarm is generated every day when bit 7 of register 7 is set to logic 1.
Similarly, an alarm is generated every hour when bit 7 of registers 7 and 5 is set to logic 1. When bit 7 of
registers 7, 5, and 3 is set to logic 1, an alarm occurs every minute when register 1 (seconds) rolls from 59
to 00.
Time-of-day alarm registers are written and read in the same format as the time-of-day registers. The
time-of-day alarm flag and interrupt is always cleared when alarm registers are read or written.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1284QN | 1 TIMER(S), REAL TIME CLOCK, PQCC28 |
| DS1286 | 1 TIMER(S), REAL TIME CLOCK, DIP28 |
| DS12885 | 1 TIMER(S), REAL TIME CLOCK, PDIP24 |
| DS12885T | 1 TIMER(S), REAL TIME CLOCK, PQFP32 |
| DS12887A | 1 TIMER(S), REAL TIME CLOCK, PDIP24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1284+ | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1284N | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1284Q | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1284Q/T&R | 制造商:Maxim Integrated Products 功能描述:IC TIMEKEEPER WATCHDOG 28-PLCC |
| DS1284Q/T&R | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。