- 您现在的位置：买卖IC网 > PDF目录9370 > DS1374U-33+T&R (Maxim Integrated Products)IC RTC I2C W/CHARGER 10-USOP PDF资料下载
参数资料
| 型号： | DS1374U-33+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/18页 |
| 文件大小： | 0K |
| 描述： | IC RTC I2C W/CHARGER 10-USOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 类型： | 二进制计数器 |
| 特点： | 警报器，方波输出，涓流充电器，监视计时器 |
| 时间格式： | 二进制 |
| 数据格式： | 二进制 |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 电压 - 电源，电池： | 1.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 带卷 (TR) |
Special Purpose Registers
The DS1374 has two additional registers (07h–08h) that
control the WD/ALM counter and the square-wave, inter-
rupt, and reset outputs.
Control Register (07h)
Bit 7/Enable Oscillator (EOSC). When set to logic 0,
the oscillator is started. When set to logic 1, the oscilla-
tor is stopped. When this bit is set to logic 1, the oscilla-
tor is stopped and the DS1374 is placed into a
low-power standby mode (IDDR). This bit is clear (logic
0) when power is first applied. When the DS1374 is
powered by VCC, the oscillator is always on regardless
of the state of the EOSC bit.
Bit 6/WD/A
AL
LM
M Counter Enable (WACE). When set to
logic 1, the WD/ALM counter is enabled. When set to
logic 0, the WD/ALM counter is disabled, and the 24
bits can be used as NV RAM. This bit is clear (logic 0)
when power is first applied.
Bit 5/WD/A
AL
LM
M Counter Select (WD/ALM). When set to
logic 0, the counter decrements every second until it
reaches zero and is then reloaded and restarted. When
set to logic 1, the WD/ALM counter decrements every
1/4096 of a second (approximately every 244s) until it
reaches zero, sets the AF bit in the status register, and
stops. If any of the WD/ALM counter registers are
accessed before the counter reaches zero, the counter
is reloaded and restarted. This bit is clear (logic 0)
when power is first applied.
Bit 4/Battery-Backed Square-Wave Enable (BBSQW).
This bit, when set to logic 1, enables the square-wave
output when VCC is absent and when the DS1374 is
being powered by the VBACKUP pin. When BBSQW is
logic 0, the SQW pin goes high impedance when VCC
falls below the power-fail trip point. This bit is disabled
(logic 0) when power is first applied.
Bit 3/Watchdog Reset Steering Bit (WDSTR). This bit
selects which output pin the watchdog-reset signal
occurs on. When the WDSTR bit is set to logic 0, a
250ms pulse occurs on the RST pin if WD/ALM = 1 and
the WD/ALM counter reaches zero. The 250ms reset
pulse occurs on the INT pin when the WDSTR bit is set
to logic 1. This bit is logic 0 when power is first applied.
Bits 2, 1/Rate Select (RS2 and RS1). These bits con-
trol the frequency of the square-wave output when the
square wave has been enabled. Table 4 shows the
square-wave frequencies that can be selected with the
RS bits. These bits are both set (logic 1) when power is
first applied.
Bit 0/Alarm Interrupt Enable (AIE). When set to logic
1, this bit permits the alarm flag (AF) bit in the status
register to assert INT (when WDSTR = 1). When set to
logic 0 or WDSTR is set to logic 0, the AF bit does not
initiate the INT signal. If the WD/ALM bit is set to logic 1
and the AF flag is set, writing AIE to zero does not trun-
cate the 250ms pulse on the INT pin. The AIE bit is at
logic 0 when power is first applied. The INT output is
available while the device is powered by either supply.
RS2
RS1
SQUARE-WAVE OUTPUT FREQUENCY
0
1Hz
0
1
4.096kHz
1
0
8.192kHz
1
32.768kHz
Table 4. Square-Wave Output Frequency
DS1374
I2C, 32-Bit Binary Counter Watchdog RTC with
Trickle Charger and Reset Input/Output
12
____________________________________________________________________
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
EOSC
WACE
WD/ALM
BBSQW
WDSTR
RS2
RS1
AIE
相关PDF资料 |
PDF描述 |
|---|---|
| DS1374U-3+T&R | IC RTC I2C W/CHARGER 10-USOP |
| DS1338U-3+T&R | IC RTC 56BYTE NV RAM 3V 8-USOP |
| VI-J6T-MZ | CONVERTER MOD DC/DC 6.5V 25W |
| VI-J6N-MZ | CONVERTER MOD DC/DC 18.5V 25W |
| VE-26B-MW | CONVERTER MOD DC/DC 95V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1375 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:2-Wire Digital Input RTC with Alarm |
| DS1375T | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1375T/T&R | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS1375T/T&R | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1375T+ | 功能描述:实时时钟 I2C Digital Input w/Alarm RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。