- 您现在的位置：买卖IC网 > PDF目录1993 > DS1388Z-3+T&R (Maxim Integrated Products)IC RTC I2C W/CHARGER 8-SOIC PDF资料下载
参数资料
| 型号： | DS1388Z-3+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/19页 |
| 文件大小： | 0K |
| 描述： | IC RTC I2C W/CHARGER 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 时钟/日历 |
| 特点： | EEPROM，闰年，监控器，涓流充电器，监视计时器 |
| 存储容量： | 512B |
| 时间格式： | HH:MM:SS:hh（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 3.3 V |
| 电压 - 电源，电池： | 1.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
I2C RTC/Supervisor with Trickle Charger
and 512 Bytes EEPROM
16
Maxim Integrated
DS1388
Device Addressing
The slave address byte is the first byte received follow-
ing the START condition from the master device. The
slave address byte consists of a 4-bit control code. For
the DS1388, this is set as 1101 binary for read and
write operations. The next three bits of the slave
address byte are the block select bits (B2, B1, B0). B2
is always logic 0 for the DS1388. These bits are used
by the master device to select which of the three blocks
in the memory map are to be accessed. These bits are
the three most significant bits of the word address. The
last bit of the slave address byte defines the operation
to be performed. When set to 1, a read operation is
selected; when set to 0, a write operation is selected.
Write Operation
Slave Receiver Mode (Write Mode)
Following the START condition from the master, the
device code (4 bits); the block address (3 bits); and the
R/W bit, which is logic-low, is placed onto the bus by
the master transmitter. This indicates to the DS1388
that a byte with a word address follows after the
DS1388 has generated an acknowledge bit during the
ninth clock cycle. The next byte transmitted by the
master is the word address and will set the internal
address pointer of the DS1388, with the DS1388
acknowledging the transfer on the ninth clock cycle.
The master device can then transmit zero or more
bytes of data, with the DS1388 acknowledging the
transfer on the ninth clock cycle. The master generates
a STOP condition to terminate the data write.
Byte Write
The write-slave address byte and word address are
transmitted to the DS1388 as described in the
Slave
Receiver Mode section. The master transmits one data
byte, with the DS1388 acknowledging the transfer on
the ninth clock cycle. The master then generates a
STOP condition to terminate the data write. This initiates
the internal write cycle, and, if the write was to the
EEPROM, the DS1388 does not generate acknowledge
signals during the internal EEPROM write cycle.
EEPROM Page Write
The write-slave address byte, word address, and the
first data byte are transmitted to the DS1388 in the
same way as in a byte write. But instead of generating
a STOP condition, the master transmits up to 8 data
bytes to the DS1388, which are temporarily stored in
the on-chip page buffer and are written into the memo-
ry after the master has transmitted a STOP condition.
Data bytes within the page that are not written remain
unchanged. The internal address pointer automatically
increments after each byte is written.
If the master should transmit more than 8 data bytes prior
to generating the STOP condition, the address pointer
rolls over and the previously received data is overwritten.
As with the byte write operation, once the STOP condi-
tion is received an internal write cycle begins.
RTC Multibyte Write
Writing multiple bytes to the RTC works much the same
way as the EEPROM page write, except that the entire
contents of block 0h can be written at once. The 8-byte
page size limitation does not apply to the block 0. If the
master should transmit more bytes than exists in block
0 prior to generating the STOP condition, the internal
address pointer rolls over and the previously received
data is overwritten. As with the byte write operation,
once the STOP condition is received an internal write
cycle begins.
Slave Address Byte
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
1
0
1
B2B1B0
R/W
OPERATION
CONTROL CODE
BLOCK SELECT
R/W
Read Clock
1101
000
1
Write Clock
1101
000
0
Read Lower Block of EEPROM
1101
001
1
Write Lower Block of EEPROM
1101
001
0
Read Upper Block of EEPROM
1101
010
1
Write Upper Block of EEPROM
1101
010
0
相关PDF资料 |
PDF描述 |
|---|---|
| DS1391U-3+ | IC RTC W/CHARGER 10-USOP |
| DS1394U-33+T&R | IC RTC SPI 3WIRE W/CHRGR 10-MSOP |
| DS14285SN+T&R | IC RTC W/NV RAM CNTRL 24-SOIC |
| DS1486P-120+ | IC TIMEKEEPER RAM 1MB 34-PCM |
| DS1500WE | IC RTC Y2KC W/NV CTRL 32-TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1388Z-5 | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1388Z-5+ | 功能描述:实时时钟 I2C RTC/Supervisor w/Trickle Charger RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1390 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Voltage SPI/3-Wire RTCs with Trickle Charger |
| DS1390_07 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Voltage SPI/3-Wire RTCs with Trickle Charger |
| DS1390_09 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Voltage SPI/3-Wire RTCs with Trickle Charger |
发布紧急采购，3分钟左右您将得到回复。