参数资料
型号: DS1394U-33+T&R
厂商: Maxim Integrated Products
文件页数: 3/26页
文件大小: 0K
描述: IC RTC SPI 3WIRE W/CHRGR 10-MSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 3,000
类型: 时钟/日历
特点: 警报器,闰年,方波输出,涓流充电器
时间格式: HH:MM:SS:hh(12/24 小时)
数据格式: YY-MM-DD-dd
接口: SPI
电源电压: 2.97 V ~ 5.5 V
电压 - 电源,电池: 1.3 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)
供应商设备封装: 10-µMAX
包装: 带卷 (TR)
DS1390–DS1394
Low-Voltage SPI/3-Wire RTCs with
Trickle Charger
11
Maxim Integrated
Pin Description
PIN
DS1390/
DS1394
DS1391
DS1392
DS1393
NAME
FUNCTION
1
X1
2
X2
Connections for Standard 32.768kHz Quartz Crystal. The internal oscillator
circuitry is designed for operation with a crystal having a 6pF specified load
capacitance (CL). Pin X1 is the input to the oscillator and can optionally be
connected to an external 32.768kHz oscillator. The output of the internal
oscillator, pin X2, is floated if an external oscillator is connected to pin X1.
3
VBACKUP
DC Backup Power Input for Primary Cell. This pin is a rechargeable
battery/super cap or a secondary supply. UL recognized to ensure against
reverse charging current when used with a lithium battery (www.maxim-
ic.com/qa/info/w/). This pin must be grounded if not used. Diodes in series
between the battery and the VBACKUP pin may prevent proper operation.
4
CS
SPI Chip-Select Input. This pin is used to select or deselect the part.
4
CE
Chip Enable for 3-Wire Interface
5
GND
Ground
6
DIN
SPI Data Input. This pin is used to shift address and data into the part.
6
INT
Interrupt Output. This pin is used to output the interrupt signal, if enabled by
the control register. The maximum voltage on this pin is 5.5V, independent
of VCC or VBACKUP. If enabled,
INT functions when the device is powered
by either VCC or VBACKUP.
9
6
RST
Reset. This active-low, open-drain output indicates the status of VCC relative
to the VPF specification. As Vcc falls below VPF, the
RST pin is driven low.
When Vcc exceeds VPF, for tRST, the
RST pin is driven high impedance.
This pin is combined with a debounced pushbutton input function. This pin
can be activated by a pushbutton reset request. This pin has an internal,
50k
(typ) pullup resistor to VCC. No external pullup resistors should be
connected. If the crystal oscillator is disabled, the startup time of the
oscillator is added to the tRST delay.
7
DOUT
SPI Data Output. Data is output on this pin when the part is in read mode.
CMOS push-pull driver.
7
I/O
Input/Output for 3-Wire Interface. CMOS push-pull driver.
8
SCLK
Serial Clock Input. This pin is used to control the timing of data into and out
of the part.
9
9
SQW/
INT
Square-Wave/Interrupt Output. This pin is used to output the programmable
square wave or interrupt signal. When enabled by setting the
ESQW bit to
logic 1, the SQW/
INT pin outputs one of four frequencies: 32.768kHz,
8.192kHz, 4.096kHz, or 1Hz. This pin is open drain and requires an external
pullup resistor. The maximum voltage on this pin is 5.5V, independent of
VCC or VBACKUP. If enabled, SQW/
INT functions when the device is powered
by either VCC or VBACKUP. If not used, this pin can be left open.
9
SQW
Square-Wave Output. This pin is open drain and requires an external pullup
resistor. The maximum voltage on this pin is 5.5V, independent of VCC or
VBACKUP. If enabled, SQW functions when the device is powered by either
VCC or VBACKUP. If not used, this pin can be left open.
10
VCC
DC Power Pin for Primary Power Supply
相关PDF资料
PDF描述
DS14285SN+T&R IC RTC W/NV RAM CNTRL 24-SOIC
DS1486P-120+ IC TIMEKEEPER RAM 1MB 34-PCM
DS1500WE IC RTC Y2KC W/NV CTRL 32-TSOP
DS1501YSN+T&R IC RTC WDOG Y2K 5V IND 28-SOIC
DS1553P-70+ IC RTC RAM Y2K 5V 70NS 34-PCM
相关代理商/技术参数
参数描述
DS1395 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:RAMified Real Time Clock
DS1395N 制造商:未知厂家 制造商全称:未知厂家 功能描述:Peripheral IC
DS1395S 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:RAMified Real Time Clock
DS1395SN 制造商:未知厂家 制造商全称:未知厂家 功能描述:Peripheral IC
DS1397 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:RAMified Real Time Clock