参数资料
型号: DS14285QN
厂商: DALLAS SEMICONDUCTOR
元件分类: Timer or RTC
英文描述: 1 TIMER(S), REAL TIME CLOCK, PQCC28
封装: PLASTIC, LCC-28
文件页数: 5/25页
文件大小: 303K
代理商: DS14285QN
DS14285/DS14287
13 of 25
NONVOLATILE RAM
The 114 general purpose nonvolatile RAM bytes are not dedicated to any special function within the
DS14285/DS14287. They can be used by the processor program as nonvolatile memory and are fully
available during the update cycle.
The DS14285/DS14287 can also provide additional nonvolatile RAM. This is accomplished through the
use of its internal lithium cell in the case of the DS14287 (or the energy source connected to the VBAT pin
in the case of the DS14285) and battery-backup controller to make a standard CMOS SRAM nonvolatile
during power-fail conditions. During power-fail, the DS14285/DS14287 automatically write-protects the
external SRAM and provides a VCC output sourced from the internal lithium cell. The interface between
the DS14285/DS14287 and an external SRAM is illustrated in Figure 3.
EXTERNAL SRAM INTERFACE TO THE DS14285/DS14287 RTC Figure 3
INTERRUPTS
The RTC plus RAM includes three separate, fully automatic sources of interrupt for a processor. The
alarm interrupt can be programmed to occur at rates from once per second to once per day. The periodic
interrupt can be selected for rates from 500 ms to 122
s. The update-ended interrupt can be used to
indicate to the program that an update cycle is complete. Each of these independent interrupt conditions is
described in greater detail in other sections of this text.
The processor program can select which interrupts, if any, are going to be used. Three bits in Register B
enable the interrupts. Writing a logic 1 to an interrupt-enable bit permits that interrupt to be initiated when
the event occurs. A 0 in an interrupt-enable bit prohibits the IRQ pin from being asserted from that
interrupt condition. If an interrupt flag is already set when an interrupt is enabled, IRQ is immediately set
at an active level, although the interrupt initiating the event may have occurred much earlier. As a result,
there are cases where the program should clear such earlier initiated interrupts before first enabling new
interrupts. When an interrupt event occurs, the relating flag bit is set to logic 1 in Register C. These flag
bits are set independent of the state of the corresponding enable bit in Register B. The flag bit can be used
in a polling mode without enabling the corresponding enable bits. The interrupt flag bit is a status bit
which software can interrogate as necessary. When a flag is set, an indication is given to software that an
interrupt event has occurred since the flag bit was last read; however, care should be taken when using the
flag bits as they are cleared each time Register C is read. Double latching is included with Register C so
相关PDF资料
PDF描述
DS14285S 1 TIMER(S), REAL TIME CLOCK, PDSO24
DS14285N 1 TIMER(S), REAL TIME CLOCK, PDIP24
DS14285SN 1 TIMER(S), REAL TIME CLOCK, PDSO24
DS14285Q 1 TIMER(S), REAL TIME CLOCK, PQCC28
DS14285 1 TIMER(S), REAL TIME CLOCK, PDIP24
相关代理商/技术参数
参数描述
DS14285QN+ 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
DS14285S 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
DS14285S/T&R 制造商:Maxim Integrated Products 功能描述:IC RTC W/NV RAM CNTRL 24-SOIC
DS14285S/T&R 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
DS14285S/TR 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Real-Time Clock with NV RAM