参数资料
型号: DS1629S+T&R
厂商: Maxim Integrated
文件页数: 11/23页
文件大小: 490K
描述: IC THERM/RTC/CALENDAR DIG 8-SOIC
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
功能: 温度计,恒温计
传感器类型: 内部
感应温度: -55°C ~ 125°C
精确度: ±2°C(最小值)
拓扑: ADC,比较器,振荡器,寄存器库
输出类型: I²C?/SMBus?
输出警报:
输出风扇:
电源电压: 2.7 V ~ 5.5 V
工作温度: -55°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOIC
包装: 带卷 (TR)
DS1629
 
11 of 23
 
CAL = Clock Alarm Latch. This volatile status bit will be set to 1 when the clock comparator becomes 
active. Once set, it will remain latched until DS1629 power is cycled. A 0 in this location indicates the
clock has never been in an alarm condition since the DS1629 was powered-up. This is a read-only bit
(writes to this location constitute a dont care) and the power-up default is the flag cleared (CAL = 0).
 
TAL =  Thermal  Alarm  Latch.  This  volatile  status  bit  will  be  set  to  1  when  the  thermal  comparator 
becomes active. Once set, it will remain latched until DS1629 power is cycled. A 0 in this location
indicates the DS1629 temperature has never exceeded T
H
 since power-up. This is a read-only bit (writes
to this location constitute a dont care) and the power-up default is the flag cleared (TAL = 0).
 
0 = Dont care. Dont care on a write, but will always read out as a 0. 
 
2-WIRE SERIAL DATA BUS
The DS1629 supports a bidirectional two-wire bus and data transmission protocol. A device that sends
data onto the bus is defined as a transmitter, and a device receiving data as a receiver. The device that
controls the message is called a master. The devices that are controlled by the master are slaves. The
bus must be controlled by a master device which generates the serial clock (SCL), controls the bus access,
and generates the START and STOP conditions. The DS1629 operates as a slave on the 2-wire bus.
Connections to the bus are made via the open-drain I/O lines SDA and SCL.
 
The following bus protocol has been defined:
 
"   Data transfer may be initiated only when the bus is not busy.
 
"   During data transfer, the data line must remain stable whenever the clock line is high. Changes in the
data line while the clock line is high will be interpreted as control signals.
 
Accordingly, the following bus conditions have been defined:
 
Bus not busy: Both data and clock lines remain high. 
 
Start data transfer: A change in the state of the data line, from high to low, while the clock is high, 
defines a START condition.
 
Stop data transfer: A change in the state of the data line, from low to high, while the clock line is HIGH, 
defines the STOP condition.
 
Data valid: The state of the data line represents valid data when, after a START condition, the data line 
is stable for the duration of the high period of the clock signal. The data on the line must be changed
during the low period of the clock signal. There is one clock pulse per bit of data.
 
Each data transfer is initiated with a START condition and terminated with a STOP condition. The
number of data bytes transferred between START and STOP conditions is not limited, and is determined
by the master device. The information is transferred byte-wise and each receiver acknowledges with a 9th
bit.
 
 
The maximum clock rate of the DS1629 is 400kHz.
 
相关PDF资料
PDF描述
DS1631S+T&R IC THERMOMETER DIG HI-PREC 8SOIC
DS1721U+T&R IC THERMOMETER/STAT DIG HP 8USOP
DS1722S IC THERMOMETER DIG 3-WIRE 8-SOIC
DS1775R7+T&R IC THERMOM/STAT DIG 111 SOT-23-5
DS1821C+ IC THERMOMETER/STAT PROG 3-TO92
相关代理商/技术参数
参数描述
DS1630AB-100-IND 制造商:未知厂家 制造商全称:未知厂家 功能描述:NVRAM (Battery Based)
DS1630AB-120-IND 制造商:未知厂家 制造商全称:未知厂家 功能描述:NVRAM (Battery Based)
DS1630AB-70-IND 制造商:未知厂家 制造商全称:未知厂家 功能描述:NVRAM (Battery Based)
DS1630AB-85-IND 制造商:未知厂家 制造商全称:未知厂家 功能描述:NVRAM (Battery Based)
DS1630ABL-100 制造商:未知厂家 制造商全称:未知厂家 功能描述:NVRAM (Battery Based)