- 您现在的位置：买卖IC网 > PDF目录21990 > DS1631UT/T&R (Maxim Integrated)IC DIGITAL THERM HI PREC 8MSOP PDF资料下载
参数资料
| 型号： | DS1631UT/T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/16页 |
| 文件大小： | 435K |
| 描述： | IC DIGITAL THERM HI PREC 8MSOP |
| 标准包装： | 3,000 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±2°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
| 其它名称： | DS1631UT&R Q1873117 |
DS1631/DS1631A/DS1731
11 of 15
2-WIRE SERIAL DATA BUS
The DS1631, DS1631A, and DS1731 communicate over a bidirectional 2-wire serial data bus that
consists of a serial clock (SCL) signal and serial data (SDA) signal. The DS1631, DS1631A, and DS1731
interface to the bus through their SCL input pins and open-drain SDA I/O pins.
The following terminology is used to describe 2-wire communication:
Master Device: Microprocessor/microcontroller that controls the slave devices on the bus. The master
device generates the SCL signal and START and STOP conditions.
Slave: All devices on the bus other than the master. The DS1631, DS1631A, and DS1731 always
function as slaves.
Bus Idle or Not Busy: Both SDA and SCL remain high. SDA is held high by a pullup resistor when the
bus is idle, and SCL must either be forced high by the master (if the SCL output is push-pull) or pulled
high by a pullup resistor (if the SCL output is open-drain).
Transmitter: A device (master or slave) that is sending data on the bus.
Receiver: A device (master or slave) that is receiving data from the bus.
START Condition: Signal generated by the master to indicate the beginning of a data transfer on the
bus. The master generates a START condition by pulling SDA from high to low while SCL is high (see
Figure 8). A repeated START is sometimes used at the end of a data transfer (instead of a STOP) to
indicate that the master will perform another operation.
STOP Condition: Signal generated by the master to indicate the end of a data transfer on the bus. The
master generates a STOP condition by transitioning SDA from low to high while SCL is high (see Figure
8). After the STOP is issued, the master releases the bus to its idle state.
Acknowledge (ACK): When a device is acting as a receiver, it must generate an acknowledge (ACK) on
the SDA line after receiving every byte of data. The receiving device performs an ACK by pulling the
SDA line low for an entire SCL period (see Figure 8). During the ACK clock cycle, the transmitting
device must release SDA. A variation on the ACK signal is the not acknowledge (NACK). When the
master device is acting as a receiver, it uses a NACK instead of an ACK after the last data byte to indicate
that it is finished receiving data. The master indicates a NACK by leaving the SDA line high during the
ACK clock cycle.
Slave Address: Every slave device on the bus has a unique 7-bit address that allows the master to access
that device. The 7-bit bus address is 1 0 0 1 A
2
A
1
A
0
, where A
2
, A
1
, and A
0
are user-selectable through
the corresponding input pins. The three address pins allow up to eight DS1631s, DS1631As, or DS1731s
to be multidropped on the same bus.
Control Byte: The control byte is transmitted by the master and consists of the 7-bit slave address plus a
read/write (R/W?/SPAN>?/SPAN>) bit (see Figure 7). If the master is going to read data from the slave device then R/W?/SPAN>?/SPAN> =
1, and if the master is going to write data to the slave device then R/W?/SPAN>?/SPAN> = 0.
Command Byte: The command byte can be any of the command protocols described in the COMMAND
SET section of this data sheet.
Figure 7. CONTROL BYTE
bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
1
0
0
1
A
2
A
1
A
0
R/W?/SPAN>?/SPAN>
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B6R-CX | CONVERTER MOD DC/DC 7.5V 75W |
| VI-B6M-CX | CONVERTER MOD DC/DC 10V 75W |
| VI-27N-CW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
| VI-B6M-CW | CONVERTER MOD DC/DC 10V 100W |
| XC3S100E-4TQG144C | IC SPARTAN-3E FPGA 100K 144-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1631Z | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1631Z/T&R | 制造商:Maxim Integrated Products 功能描述:0.5C 12C TEMP SENSOR 150S08 T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG HI-PREC 8SOIC |
| DS1631Z/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1631Z/TR | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Precision Digital Thermometer and Thermostat |
| DS1631Z+ | 功能描述:板上安装温度传感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。