- 您现在的位置：买卖IC网 > PDF目录21990 > DS1631UT/T&R (Maxim Integrated)IC DIGITAL THERM HI PREC 8MSOP PDF资料下载
参数资料
| 型号： | DS1631UT/T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 12/16页 |
| 文件大小： | 435K |
| 描述： | IC DIGITAL THERM HI PREC 8MSOP |
| 标准包装： | 3,000 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±2°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
| 其它名称： | DS1631UT&R Q1873117 |
DS1631/DS1631A/DS1731
12 of 15
Figure 8. START, STOP, AND ACK SIGNALS
GENERAL 2-WIRE INFORMATION
All data is transmitted MSb first over the 2-wire bus.
One bit of data is transmitted on the 2-wire bus each SCL period.
A pullup resistor is required on the SDA line and, when the bus is idle, both SDA and SCL must remain
in a logic-high state.
All bus communication must be initiated with a START condition and terminated with a STOP
condition. During a START or STOP is the only time SDA is allowed to change states while SCL is
high. At all other times, changes on the SDA line can only occur when SCL is low: SDA must remain
stable when SCL is high.
After every 8-bit (1-byte) transfer, the receiving device must answer with an ACK (or NACK), which
takes one SCL period. Therefore, nine clocks are required for every one-byte data transfer.
INITIATING 2-WIRE COMMUNICATION
To initiate 2-wire communication, the master generates a START followed by a control byte containing
the DS1631, DS1631A, or DS1731 slave address. The R/W?/SPAN>?/SPAN> bit of the control byte must be a 0 ( write )
since the master next writes a command byte. The DS1631/DS1631A/DS1731 responds with an ACK
after receiving the control byte. This must be followed by a command byte from the master, which
indicates what type of operation is to be performed. The DS1631/DS1631A/DS1731 again respond with
an ACK after receiving the command byte.
If the command byte is a Start Convert T or Stop Convert T command (see Figure 9a), the transaction is
finished, and the master must issue a STOP to signal the end of the communication sequence. If the
command byte indicates a write or read operation, additional actions must occur as explained in the
following sections.
2-WIRE WRITES
The master can write data to the DS1631/DS1631A/DS1731 by issuing an Access Config, Access TH, or
Access TL command following the control byte (see Figures 9b and 9d). Since the R/W?/SPAN>?/SPAN> bit in the control
byte was a 0 ( write ), the DS1631/DS1631A/DS1731 are already prepared to receive data. Therefore,
after receiving an ACK in response to the command byte, the master device can immediately begin
transmitting data. When writing to the configuration register, the master must send one byte of data, and
when writing to the T
H
or T
L
registers the master must send two bytes of data. After receiving each data
byte, the DS1631/DS1631A/DS1731 respond with an ACK, and the transaction is finished with a STOP
from the master.
SCL
SDA
START
Condition
STOP
Condition
ACK (or NACK)
From Receiver
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B6R-CX | CONVERTER MOD DC/DC 7.5V 75W |
| VI-B6M-CX | CONVERTER MOD DC/DC 10V 75W |
| VI-27N-CW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
| VI-B6M-CW | CONVERTER MOD DC/DC 10V 100W |
| XC3S100E-4TQG144C | IC SPARTAN-3E FPGA 100K 144-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1631Z | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1631Z/T&R | 制造商:Maxim Integrated Products 功能描述:0.5C 12C TEMP SENSOR 150S08 T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG HI-PREC 8SOIC |
| DS1631Z/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1631Z/TR | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:High-Precision Digital Thermometer and Thermostat |
| DS1631Z+ | 功能描述:板上安装温度传感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。