- 您现在的位置：买卖IC网 > PDF目录21999 > DS1780E (Maxim Integrated)IC CPU PERIPHERAL MON 24-TSSOP PDF资料下载
参数资料
| 型号： | DS1780E |
| 厂商： | Maxim Integrated |
| 文件页数： | 12/28页 |
| 文件大小： | 0K |
| 描述： | IC CPU PERIPHERAL MON 24-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 62 |
| 功能： | 温度监控器，CPU 外围设备 |
| 传感器类型： | 内部 |
| 感应温度： | -40°C ~ 125°C |
| 精确度： | ±12°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，风扇速度控制，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 2.8 V ~ 5.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
DS1780
OPERATION - Interrupts
An external interrupt can come from the following sources. While the label suggests a specific type or
source of interrupt, this label is not a restriction on the usage; it could come from any desired source.
1. Analog Voltage: An interrupt will be generated if a analog voltage high or low limit has been
exceeded; this is generally when a power supply is out of its normal operating range.
2. Temperature: An interrupt will be generated if a high or a low hot temperature limit has been
exceeded.
3. Fan speed: An interrupt will be generated if a fan count limit has been exceeded.
4. Chassis Intrusion: This is an active high interrupt from any type of device that detects and captures
chassis intrusion violations. This could be accomplished mechanically, optically, or electrically, and
circuitry external to the DS1780 is expected to latch the event.
All System Management Interrupts (SMIs) are indicated in the two Interrupt Status Registers. The INT
output has individual mask registers and individual masks for each Interrupt. As described in the
“OPERATION - Configuration Register” Section, this hardware Interrupt line can also be
enabled/disabled in the Configuration Register.
Reading an Interrupt Status Register will output the contents of the Register, and reset the Register. A
subsequent read done before the analog ‘round-robin’ monitoring loop is complete will indicate a cleared
Register. Allow at least 1 second to allow all Registers to be updated between reads. In summary, the
Interrupt Status Register clears upon being read, and requires at least 1 second to be updated. When the
Interrupt Status Register clears, the hardwire interrupt line will also clear until the Registers are updated
by the monitoring loop.
The INT hardware Interrupt output is cleared with the INT_Clear bit, which is Bit 3 of the Configuration
Register, without affecting the contents of the Interrupt Status Registers. When this bit is high, the
DS1780 monitoring loop will stop. It will resume when the bit is low.
Analog Voltage Limits
The limits for the analog voltage comparison are programmed into the Value RAM at Internal Address
Registers 2Bh - 36h. A high and low limit is associated with each of the 6 analog voltage inputs of the
DS1780. Care must be taken to program the limit registers in the same format as the respective voltage
data register. Please see “OPERATION - Voltage Data Format” for details. For setting a voltage
interrupt, the DS1780 compares on a “greater than” basis for high limits and a “less than or equal to”
basis for low limits. The host can mask any or all of the voltage limits for interrupt contention.
Temperature Limits and Interrupt Modes
The host programs an 8-bit high temperature limit and hysteresis/low temperature limit into the DS1780
at Internal Address Registers 39h and 3 Ah in the same two’s complement format described in the
“OPERATION - Temperature Data Format” section. The temperature mode is programmed into the
Temperature Configuration Register (0x4Bh). A digital 8-bit comparator is also incorporated that
compares the temperature readings to the programmed limits.
There are three interrupt modes of operation. The INT output can be programmed for either of the three
interrupt modes of operation a nd the host can program the DS1780 to completely mask temperature
interrupts from controlling the INT output.
12 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| EBC08DCAH | CONN EDGECARD 16POS R/A .100 SLD |
| DS1620S | IC THERMOMETER/STAT DIG 8-SOIC |
| EBC08DCAD | CONN EDGECARD 16POS R/A .100 SLD |
| DS1620 | IC THERMOMETER/STAT DIG 8-DIP |
| DS1629S | IC THERM/RTC/CALENDAR DIG 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1780E/T&R | 制造商:Maxim Integrated Products 功能描述:PC HARDWARE MONITOR T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CPU PERIPHERAL MON 24-TSSOP |
| DS1780E/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1780E/TR | 制造商:Maxim Integrated Products 功能描述:Data Acquisition System, 6 Channel, 8 Bit, 24 Pin, Plastic, TSSOP |
| DS1780E+ | 功能描述:板上安装温度传感器 CPU Peripheral Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1780E+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 24TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CPU PERIPHERAL MON 24-TSSOP 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors CPU Peripheral Monitor |
发布紧急采购，3分钟左右您将得到回复。