参数资料
型号: DS1780E
厂商: Maxim Integrated
文件页数: 17/28页
文件大小: 0K
描述: IC CPU PERIPHERAL MON 24-TSSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 62
功能: 温度监控器,CPU 外围设备
传感器类型: 内部
感应温度: -40°C ~ 125°C
精确度: ±12°C(最小值)
拓扑: ADC(三角积分型),比较器,风扇速度控制,寄存器库
输出类型: I²C?/SMBus?
输出警报:
输出风扇:
电源电压: 2.8 V ~ 5.75 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 24-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 24-TSSOP
包装: 管件
DS1780
CONFIGURATION REGISTER (ADDRESS 0X40; POWER-UP DEFAULT = 08h)
Table 10.2
BIT
NAME
R/W
DESCRIPTION
Logic 1 enables startup of measurement loop, logic 0 places the DS1780 in standby mode.
Caution: The INT output pin will not be cleared if the user writes a 0 to this location after an
0
START
R/W
interrupt has occurred (see “ INT Clear” bit). At startup, limit checking functions and
scanning begins. Note, all HIGH and LOW LIMITS should be set into the DS1780 prior to
turning on this bit. (Power-up default=0).
1
2
3
INT Enable
Reserved
INT Clear
R/W
R/W
R/W
Logic 1 enables the INT output. 1=Enabled 0=Disabled (Power-up Default = 0)
Power-up Default = 0.
During Interrupt Service Routine (ISR) this bit asserted logic 1 clears INT output without
affecting the contents of the Interrupt Status Registers. The device will stop monitoring. It
will resume upon clearing of this bit. (Power-up default=1.)
4
5
6
RESET
Reserved
CHS Reset
R/W
R/W
R/W
Creates a RESET (Active Low) signal for 20 ms (min) on the RST output. (Power-up
default = 0) This bit is cleared once the RST pulse goes active.
Power-up Default = 0.
Logic 1 resets the chassis intrusion pin. (Power-up default = 0) This bit is cleared after CHS
becomes cleared.
Logic 1 restores power-up default values to all DS1780 registers except for the analog
7
Initialization
R/W
output and value RAM, which remain unchanged. This bit automatically clears itself since
the power on default is 0.
INTERRUPT INT STATUS REGISTER 1 (ADDRESS 0X41; POWER-UP
DEFAULT = 00h) Table 10.3
BIT
0
1
2
3
NAME
+2.5V_Error
V CCP1 _Errror
+3.3V_Error
+5V_Error
R/W
R
R
R
R
DESCRIPTION
A 1 indicates a High or Low limit has been exceeded.
A 1 indicates a High or Low limit has been exceeded.
A 1 indicates a High or Low limit has been exceeded.
A 1 indicates a High or Low limit has been exceeded.
A 1 indicates that a high or low temperature limit has been exceeded. The conditions that
4
Temp_Error
R
will generate and clear this bit depend upon the temperature interrupt mode chosen. The
mode is set at bits 0 and 1 of the Temperature Configuration Register (0x48h).
5
6
7
Reserved
FAN1_Error
FAN2_Error
R
R
R
0
A 1 indicates that a fan count limit has been exceeded.
A 1 indicates that a fan count limit has been exceeded.
17 of 28
相关PDF资料
PDF描述
EBC08DCAH CONN EDGECARD 16POS R/A .100 SLD
DS1620S IC THERMOMETER/STAT DIG 8-SOIC
EBC08DCAD CONN EDGECARD 16POS R/A .100 SLD
DS1620 IC THERMOMETER/STAT DIG 8-DIP
DS1629S IC THERM/RTC/CALENDAR DIG 8-SOIC
相关代理商/技术参数
参数描述
DS1780E/T&R 制造商:Maxim Integrated Products 功能描述:PC HARDWARE MONITOR T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CPU PERIPHERAL MON 24-TSSOP
DS1780E/T&R 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1780E/TR 制造商:Maxim Integrated Products 功能描述:Data Acquisition System, 6 Channel, 8 Bit, 24 Pin, Plastic, TSSOP
DS1780E+ 功能描述:板上安装温度传感器 CPU Peripheral Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1780E+T&R 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 24TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CPU PERIPHERAL MON 24-TSSOP 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors CPU Peripheral Monitor