- 您现在的位置：买卖IC网 > PDF目录97865 > DS1822 (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT PDF资料下载
参数资料
| 型号： | DS1822 |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| 封装： | TO92-3 |
| 文件页数： | 19/21页 |
| 文件大小： | 222K |
| 代理商： | DS1822 |
DS1822
7 of 21
MEMORY
The DS1822’s memory is organized as shown in Figure 7. The memory consists of an SRAM scratchpad
with NV EEPROM storage for the high and low alarm trigger registers (TH and TL) and configuration
register. Note that if the DS1822 alarm function is not used, the TH and TL registers can serve as general-
purpose memory. All memory commands are described in detail in the DS1822 FUNCTION
COMMANDS section.
Byte 0 and byte 1 of the scratchpad contain the LSB and the MSB of the temperature register,
respectively. These bytes are read-only. Bytes 2 and 3 provide access to TH and TL registers. Byte 4
contains the configuration register data, which is explained in detail in the CONFIGURATION
REGISTER section of this data sheet. Bytes 5, 6, and 7 are reserved for internal use by the device and
cannot be overwritten.
Byte 8 of the scratchpad is read-only and contains the cyclic redundancy check (CRC) code for bytes 0
through 7 of the scratchpad. The DS1822 generates this CRC using the method described in the CRC
GENERATION section.
Data is written to bytes 2, 3, and 4 of the scratchpad using the Write Scratchpad [4Eh] command; the data
must be transmitted to the DS1822 starting with the least significant bit of byte 2. To verify data integrity,
the scratchpad can be read (using the Read Scratchpad [BEh] command) after the data is written. When
reading the scratchpad, data is transferred over the 1-Wire bus starting with the least significant bit of
byte 0. To transfer the TH, TL and configuration data from the scratchpad to EEPROM, the master must
issue the Copy Scratchpad [48h] command.
Data in the EEPROM registers is retained when the device is powered down; at power-up the EEPROM
data is reloaded into the corresponding scratchpad locations. Data can also be reloaded from EEPROM to
the scratchpad at any time using the Recall E
2
[B8h] command. The master can issue read time slots
following the Recall E
2 command and the DS1822 will indicate the status of the recall by transmitting 0
while the recall is in progress and 1 when the recall is done.
DS1822 MEMORY MAP Figure 7
SCRATCHPAD (Power-up State)
byte 0
Temperature LSB (50h)
byte 1
Temperature MSB (05h)
EEPROM
byte 2
TH Register or User Byte 1*
TH Register or User Byte 1
byte 3
TL Register or User Byte 2*
TL Register or User Byte 2
byte 4
Configuration Register*
Configuration Register
byte 5
Reserved (FFh)
byte 6
Reserved
byte 7
Reserved (10h)
byte 8 CRC*
*Power-up state depends on value(s) stored
in EEPROM
(85°C)
相关PDF资料 |
PDF描述 |
|---|---|
| DS1822+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822Z | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS18B20-PAR/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
| DS18B20-PAR | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
| DS18B20P | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1822/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+ | 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+PAR | 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Econo 1-Wire Digital Thermometer |
| DS1822+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors 1-Wire Digital Thermometer |
发布紧急采购，3分钟左右您将得到回复。