- 您现在的位置：买卖IC网 > PDF目录97865 > DS1822 (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT PDF资料下载
参数资料
| 型号： | DS1822 |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| 封装： | TO92-3 |
| 文件页数： | 21/21页 |
| 文件大小： | 222K |
| 代理商： | DS1822 |
DS1822
9 of 21
is available in Application Note 27 entitled Understanding and Using Cyclic Redundancy Checks with
Dallas Semiconductor Touch Memory Products.
CRC GENERATOR Figure 9
1-WIRE BUS SYSTEM
The 1-Wire bus system uses a single bus master to control one or more slave devices. The DS1822 is
always a slave. When there is only one slave on the bus, the system is referred to as a “single-drop”
system; the system is “multidrop” if there are multiple slaves on the bus.
All data and commands are transmitted least significant bit first over the 1-Wire bus.
The following discussion of the 1-Wire bus system is broken down into three topics: hardware
configuration, transaction sequence, and 1-Wire signaling (signal types and timing).
HARDWARE CONFIGURATION
The 1-Wire bus has by definition only a single data line. Each device (master or slave) interfaces to the
data line via an open drain or 3-state port. This allows each device to “release” the data line when the
device is not transmitting data so the bus is available for use by another device. The 1-Wire port of the
DS1822 (the DQ pin) is open drain with an internal circuit equivalent to that shown in Figure 10.
The 1-Wire bus requires an external pullup resistor of approximately 5 k
Ω; thus, the idle state for the 1-
Wire bus is high. If for any reason a transaction needs to be suspended, the bus MUST be left in the idle
state if the transaction is to resume. Infinite recovery time can occur between bits so long as the 1-Wire
bus is in the inactive (high) state during the recovery period. If the bus is held low for more than 480
μs,
all components on the bus will be reset.
HARDWARE CONFIGURATION Figure 10
(MSB)
(LSB)
XOR
INPUT
VPU
4.7k
5μA
Typ.
RX
TX
DS1822 1-WIRE PORT
100
Ω
MOSFET
TX
RX
RX = RECEIVE
TX = TRANSMIT
1-wire Bus
DQ
Pin
相关PDF资料 |
PDF描述 |
|---|---|
| DS1822+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822Z | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS18B20-PAR/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
| DS18B20-PAR | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
| DS18B20P | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1822/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+ | 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+PAR | 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Econo 1-Wire Digital Thermometer |
| DS1822+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors 1-Wire Digital Thermometer |
发布紧急采购，3分钟左右您将得到回复。