- 您现在的位置：买卖IC网 > PDF目录13748 > DS1830S+T&R (Maxim Integrated Products)IC SEQUENCER RESET PB 5V 8-SOIC PDF资料下载
参数资料
| 型号： | DS1830S+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/7页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCER RESET PB 5V 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 序列发生器 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 5V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
D1830/A
OPERATION — POWER MONITOR
The DS1830 provides the functions of detecting out-of-tolerance conditions on a power supply and
warning a processor based system of impending power failure. When V CC is detected as out-of-tolerance
all reset outputs will be forced active. When V CC returns to a valid state , RST1 will remain active for
period of time based on the condition of the TD input. Reset outputs RST2 and RST3 follow RST1 , each
one at the proper delays for the condition of the TD input. All resets will remain in the inactive state
(high) until the next V CC out-of-tolerance condition or pushbutton reset. On power-up all resets are kept
active for an appropriate period determined by the status of the TD input after the power supply inputs
have reached the selected tolerance. This allows the power supply and system power to stabilize before
the reset sequences are released.
BLOCK DIAGRAM Figure 1
OPERATION — TOLERANCE SELECT
The DS1830/A provides a TOL input for individual customization of the DS1830x to specific application
requirements (see Table 1). For the tolerance selection, see Table 1 below. The TOL input is only
sampled while V CC is below the lowest potential trip value and can not be changed after the V CC voltage
exceeds the lowest potential trip value.
TOL — TOLERANCE SELECT Table 1
TOL
V CC
GND
OPEN
(N.C.)
5V (DS1830)
5%
10%
15%
3.3V (DS1830A)
5%
10%
20%
2 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| DS1830AS+T&R | IC SEQUENCER RESET PB 3.3V 8SOIC |
| SCRH73B-121 | INDUCTOR SMD 120UH 0.49A 1KHZ |
| UWD1E100MCL1GS | CAP ALUM 10UF 25V 20% SMD |
| HCM25DSEF-S243 | CONN EDGECARD 50POS .156 EYELET |
| RCC22DRYS-S93 | CONN EDGECARD 44POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1830U | 功能描述:监控电路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1830U/T&R | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1830U+ | 功能描述:监控电路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1830U+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:IC SEQUENCER RESET PB 5V 8-USOP |
| DS1830U+T&R | 功能描述:监控电路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。