- 您现在的位置：买卖IC网 > PDF目录295504 > DS1845X-100 (DALLAS SEMICONDUCTOR) 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, UUC14 PDF资料下载
参数资料
| 型号： | DS1845X-100 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | 数字电位计 |
| 英文描述： | 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, UUC14 |
| 封装： | FCP-14 |
| 文件页数： | 10/13页 |
| 文件大小： | 98K |
| 代理商： | DS1845X-100 |
DS1845
6 of 13
Data valid: The state of the data line represents valid data when, after a START condition, the data line
is stable for the duration of the HIGH period of the clock signal. The data on the line can be changed
during the LOW period of the clock signal. There is one clock pulse per bit of data. Figures 2 and 3
detail how data transfer is accomplished on the two-wire bus. Depending upon the state of the R/W bit,
two types of data transfer are possible.
Each data transfer is initiated with a START condition and terminated with a STOP condition. The
number of data bytes transferred between START and STOP conditions is not limited and is determined
by the master device. The information is transferred byte-wise and each receiver acknowledges with a 9
th
bit.
Within the bus specifications a regular mode (100 kHz clock rate) and a fast mode (400 kHz clock rate)
are defined. The DS1845 works in both modes.
Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after the
reception of each byte. The master device must generate an extra clock pulse which is associated with this
acknowledge bit.
A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a
way that the SDA line is a stable LOW during the HIGH period of the acknowledge related clock pulse.
Of course, setup and hold times must be taken into account. A master must signal an end of data to the
slave by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this
case, the slave must leave the data line HIGH to enable the master to generate the STOP condition.
1. Data transfer from a master transmitter to a slave receiver. The 1
st byte transmitted by the master is
the command/control byte. Next follows a number of data bytes. The slave returns an acknowledge bit
after each received byte.
2. Data transfer from a slave transmitter to a master receiver. The master transmits the 1
st byte (the
command/control byte) to the slave. The slave then returns an acknowledge bit. Next follows a
number of data bytes transmitted by the slave to the master. The master returns an acknowledge bit
after all received bytes other than the last byte. At the end of the last received byte, a ‘not
acknowledge’ can be returned.
The master device generates all serial clock pulses and the START and STOP conditions. A transfer is
ended with a STOP condition or with a repeated START condition. Since a repeated START condition is
also the beginning of the next serial transfer, the bus will not be released.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1866N | DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDIP8 |
| DS1867-100-IND | 100K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDIP14 |
| DS2009D-65 | 512 X 9 OTHER FIFO, 65 ns, PDIP28 |
| DS500008-12 | 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 |
| DS80C310-MCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1845X-100/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV POT & MEM BUMP 10K/100K TR - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC POT/MEM DUAL NV 100K 14-FCP |
| DS1845X-100/T&R | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1846 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:NV Tri-Potentiometer, Memory, and MicroMonitor |
| DS1846E-010 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1846E-010/R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:NV Tri-Potentiometer, Memory, and MicroMonitor |
发布紧急采购，3分钟左右您将得到回复。