- 您现在的位置：买卖IC网 > PDF目录8537 > DS1851E-010+T&R (Maxim Integrated Products)IC DAC DUAL NV TEMP CNTRL 8TSSOP PDF资料下载
参数资料
| 型号： | DS1851E-010+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/18页 |
| 文件大小： | 0K |
| 描述： | IC DAC DUAL NV TEMP CNTRL 8TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 8 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 95°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 2 电压，单极 |
| 采样率（每秒）： | * |
DS1851
8 of 18
2-WIRE OPERATION
Clock and Data Transitions
The SDA pin is normally pulled high with an external resistor or device. Data on the SDA pin may only
change during SCL low time periods. Data changes during SCL high periods will indicate a START or
STOP conditions depending on the conditions discussed below. Refer to the Timing Diagram in Figure 4
for further details.
START Condition
A high-to-low transition of SDA with SCL high is a START condition that must precede any other
command. Refer to the timing diagram in Figure 4 for further details.
STOP Condition
A low-to-high transition of SDA with SCL high is a STOP condition. After a read sequence, the stop
command places the DS1851 into a low-power mode. Refer to the timing diagram in Figure 4 for further
details.
Acknowledge Bit
All address bytes and data bytes are transmitted via a serial protocol. The DS1851 pulls SDA low during
the ninth clock pulse to acknowledge that it has received each word.
Standby Mode
The DS1851 features a low-power mode that is automatically enabled after power-on, after a STOP
command, and after the completion of all internal operations.
2-Wire Interface Reset
After any interruption in protocol, power loss, or system reset, the following steps reset the DS1851:
1) Clock up to nine cycles.
2) Look for SDA high in each cycle while SCL is high.
3) Create a START condition while SDA is high.
Device Addressing
The DS1851 must receive an 8-bit device address word following a START condition to enable a specific
device for a read or write operation. The address word is clocked into the DS1851 MSB to LSB. The
address word consists of Ah (1010) followed by 000 then the R/W bit. If the R/W bit is high, a read
operation is initiated. The R/W is low, a write operation is initiated. Upon a match of the address, the
DS1851 will output a zero for one clock cycle as an acknowledge. If the address does not match, the
DS1851 ignores the communication.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1187CS8#TRPBF | IC AMP VIDEO DIFFRNC ADJ 8-SOIC |
| VI-B33-MU-F3 | CONVERTER MOD DC/DC 24V 200W |
| MAX5521ETC+T | IC DAC 10BIT SGL ULP 12-TQFN |
| VI-B5N-MX-S | CONVERTER MOD DC/DC 18.5V 75W |
| VI-B33-MU-F2 | CONVERTER MOD DC/DC 24V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1852 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Optical Transceiver Diagnostic Monitor |
| DS1852B-000 | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS1852B-000/C | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS1852B-000/T&R | 制造商:Maxim Integrated Products 功能描述:IC MONITOR TXRX OPTICAL 25-BGA |
| DS1852B-000/T&R | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。