- 您现在的位置：买卖IC网 > PDF目录1913 > DS1852B-00C+ (Maxim Integrated Products)IC MONITOR TXRX OPTICAL 25-BGA PDF资料下载
参数资料
| 型号： | DS1852B-00C+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/26页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR TXRX OPTICAL 25-BGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 103 |
| 类型： | 收发器 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 25-TFBGA，CSPBGA |
| 供应商设备封装： | 25-BGA（5x5） |
| 包装： | 托盘 |
DS1852
23 of 26
NOTES
1) All voltages are referenced to ground.
2) This is the time for one comparison. The complete cycle is this value multiplied by 3.
3) Absolute voltage error for Bin, Pin, and Rin are valid from 0% to 98%.
4) ASEL = GND, SDA = SCL = Din = Fin = Lin = RSin = VCC.
5) The time to begin monitoring operations after VCC has risen above the analog minimum voltage.
6) After STOP command has been received. No acknowledges will be issued during this interval.
7) A fast mode device can be used in a standard mode system, but the requirement tSU:DAT > 250ns must
then be met. This will automatically be the case if the device does not stretch the low period of the
SCL signal. If such a device does stretch the low period of the SCL signal, it must output the next
data bit to the SDA line tRMAX + tSU:DAT = 1000 + 250 = 1250ns before the SCL line is released.
8) After this period, the first clock pulse is generated.
9) The maximum tHD:DAT has only to be met if the device does not stretch the low period (tLOW) of the
SCL signal.
10) A device must internally provide a hold time of at least 300ns for the SDA signal (see the VIH MIN of
the SCL signal) in order to bridge the undefined region of the falling edge of SCL.
11) C
B— total capacitance of one bus line in picofarads, timing referenced to 0.9VCC and 0.1VCC.
12) Input levels equal either VCC or GND.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1854E-050 | IC RES TEMP-CNTRL 50/50K 16TSSOP |
| DS1855X-050#T&R | IC DUAL NV DGTL POT/MEM 14-FCP |
| DS1856B-030+ | IC RES TEMP-CNTRL 30/10K 16-BGA |
| DS1857E-050+ | IC RES TEMP 50/50K 2MON 16-TSSOP |
| DS1857E-050 | IC RES TEMP 50/50K 2MON 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1852B-00C+ | 功能描述:模数转换器 - ADC Optical Transceiver Diagnostic Monitor RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS1852B-00C+T&R | 制造商:Maxim Integrated Products 功能描述:OPT TRANS DIAG MON REV C1 T&R LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MONITOR TXRX OPTICAL 25-BGA 制造商:Maxim Integrated Products 功能描述:Data Converter ICs - Various Optical Transceiver Diagnostic Monitor |
| DS1852B-00C+T&R | 功能描述:模数转换器 - ADC Optical Transceiver Diagnostic Monitor RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS1854 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with Two Monitors |
| DS1854B-050 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。