- 您现在的位置：买卖IC网 > PDF目录1913 > DS1869S-C10+T&R (Maxim Integrated Products)IC RHEOSTAT DALLAST 8SOIC PDF资料下载
参数资料
| 型号： | DS1869S-C10+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | IC RHEOSTAT DALLAST 8SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 产品变化通告： | DS1869 Series Discontinuation 10/May/2012 |
| 标准包装： | 2,000 |
| 系列： | Dallastat™ |
| 接片： | 64 |
| 电阻（欧姆）： | 10k |
| 电路数： | 1 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 上/下 |
| 电源电压： | ± 2.7 V ~ 8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.209"，5.30mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | 90-1869V+C10 |
DS1869
4 of 8
DS1869 DUAL PORT CONFIGURATION (TYPICAL EXAMPLE) Figure 2B
The DS1869 is provided with two supply inputs -V and +V. The maximum voltage difference between
the two supply inputs is +8.0 volts. The minimum voltage difference is +2.7 volts. All input levels are
referenced to the negative supply input, -V. The voltage applied to any Dallastat terminal must not exceed
the negative supply voltage (-V ) by -0.5 or the positive supply voltage (+V) by +0.5 volts. The minimum
logic high level must be +2.4 volts with reference to the -V supply voltage input for +V=5V. A logic low
level with reference to the -V supply voltage has a maximum value of +0.8 volts. Dallastats exhibit a
typical wiper resistance of 400 ohms with a maximum wiper resistance of 1000 ohms. The maximum
wiper current allowed through the Dallastat is specified at 1 milliamps (see DC Electrical
Characteristics).
NONVOLATILE WIPER SETTINGS
Dallastats maintain the position of the wiper in the absence of power. This feature is provided through the
use of EEPROM type memory cell arrays. During normal operation the position of the wiper is
determined by the input multiplexer. Periodically, the multiplexer will update the EEPROM memory
cells. The manner in which an update occurs has been optimized for reliability, durability, and
performance. Additionally, the update operation is totally transparent to the user.
When power is applied to the Dallastat, the wiper setting will be the last recorded in the EEPROM
memory cells. If the Dallastat setting is changed after power is applied, the new value will be stored after
a delay of 2 seconds. The initial storage of a new value after power-up occurs when the first change is
made, regardless of when this change is made.
After the initial change on power-up all subsequent changes of the wiper position will be recorded only if
the 4
th LSB (out of a 6-bit total for 64 positions) is being changed. Thus any change greater than 12.5% of
the total resistance range will trigger one EEPROM write cycle.
Changes or storage to the EEPROM memory cells must allow for a 2-second delay to guarantee that
updates will occur. The EEPROM memory cells are specified to accept greater that 50,000 writes before a
wear-out condition. If the EEPROM memory cells do reach a wear-out condition, the Dallastat will still
function properly while power is applied. However, on power-up the device’s wiper position will be that
of the position last recorded before memory cell wear-out.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1875T+T&R | IC SFP CTRLR/TRIPLEXER 38-TQFN |
| DS1876T+T&R | IC CTRLR SFP DUAL LDD 28TQFN |
| DS1877T+T&R | IC CTLR/MON SFP 1-2CH 28TQFN |
| DS1878T+T&R | IC CTLR SFP W/DGTL LDD RX 28TQFN |
| DS1881Z-050+T&R | IC DGTL POT NV 2CH 45K 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS186E | 制造商:Banner Engineering 功能描述:Sensor, Emitter, Cable |
| DS186EQ8 | 制造商:Banner Engineering 功能描述:DS186EQ8 EURO QD EMITTER |
| DS1870 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:LDMOS RF Power-Amplifier Bias Controller |
| DS1870_06 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:LDMOS RF Power-Amplifier Bias Controller |
| DS1870E-010 | 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。