- 您现在的位置：买卖IC网 > PDF目录11653 > DS1878T+T (Maxim Integrated Products)IC CTLR SFP W/DGTL LDD RX 28TQFN PDF资料下载
参数资料
| 型号： | DS1878T+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/101页 |
| 文件大小： | 0K |
| 描述： | IC CTLR SFP W/DGTL LDD RX 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | SFP+ 控制器 |
| 输入类型： | 模拟，数字 |
| 输出类型： | 数字 |
| 接口： | I²C，LDD，串行 |
| 电流 - 电源： | 2.5mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页
DS1878
Low-Voltage Operation
The device contains two power-on reset (POR) levels.
The lower level is a digital POR (POD) and the higher
level is an analog POR (POA). At startup, before the
supply voltage rises above POA, the outputs are dis-
abled, all SRAM locations are set to their defaults,
shadowed EEPROM (SEE) locations are zero, and all
analog circuitry is disabled. When VCC reaches POA,
the SEE is recalled, and the analog circuitry is enabled.
While VCC remains above POA, the device is in its nor-
mal operating state, and it responds based on its non-
volatile configuration. If during operation VCC falls
below POA, but is still above POD, then the SRAM
retains the SEE settings from the first SEE recall, but the
device analog is shut down and the outputs disabled. If
the supply voltage recovers back above POA, then the
device immediately resumes normal operation. If the
supply voltage falls below POD, then the device SRAM
is placed in its default state and another SEE recall is
required to reload the nonvolatile settings. The
EEPROM recall occurs the next time VCC exceeds
POA. Figure 10 shows the sequence of events as the
voltage varies.
Any time VCC is above POD, the I2C interface can be
used to determine if VCC is below the POA level. This is
accomplished by checking the RDYB bit in the STATUS
(Lower Memory, Register 6Eh) byte. RDYB is set when
VCC is below POA; when VCC rises above POA, RDYB
SFP+ Controller with Digital LDD Interface
______________________________________________________________________________________
19
VPOA
VPOD
VCC
SEE
RECALLED VALUE
PRECHARGED
TO 0
PRECHARGED
TO 0
PRECHARGED TO 0
SEE RECALL
Figure 10. Low-Voltage Hysteresis Example
RSSI RESULT
FINE
FULL-SCALE
RESPONSE
COARSE
FULL-SCALE
RESPONSE
FINE
RIGHT-SHIFT
= 3
MON3 INPUT
FINE
COARSE
HYSTERESIS
Figure 9. RSSI with Crossover Disabled
相关PDF资料 |
PDF描述 |
|---|---|
| MS27484E18F66S | CONN PLUG 66POS STRAIGHT W/SCKT |
| MS27467E25A24P | CONN PLUG 24POS STRAIGHT W/PINS |
| D38999/24WG11PA | CONN RCPT 11POS JAM NUT W/PINS |
| D38999/26FH21SA | CONN PLUG 21POS STRAIGHT W/SCKT |
| 413515-7 | CONN JACK BNC RTANG 50OHM 30AU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS-187PU | 制造商:Shinagawa Shoko 功能描述: |
| DS-187U | 制造商:Shinagawa Shoko 功能描述: |
| DS1880E-050 | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1880E-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL LOG POT + EQUALIZER T&R - Tape and Reel |
| DS1880E-050/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。