参数资料
型号: DS1878T+T
厂商: Maxim Integrated Products
文件页数: 16/101页
文件大小: 0K
描述: IC CTLR SFP W/DGTL LDD RX 28TQFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
类型: SFP+ 控制器
输入类型: 模拟,数字
输出类型: 数字
接口: I²C,LDD,串行
电流 - 电源: 2.5mA
安装类型: 表面贴装
封装/外壳: 28-WFQFN 裸露焊盘
供应商设备封装: 28-TQFN-EP(5x5)
包装: 带卷 (TR)
DS1878
SFP+ Controller with Digital LDD Interface
______________________________________________________________________________________
21
LUT LOADED TO [7:0]
DAC[1/2]TI
8
7
6
5
4
3
2
1
0
DAC[1/2]TI
DAC[1/2]TC = 0
TEMPERATURE (
°C)
-40
+102
TEMPERATURE (
°C)
-40
+102
DAC[1/2]TC = 1
LUT LOADED TO [8:1]
(DAC BIT 0 = 0)
LUT LOADED TO [8:1]
(DAC BIT 0 = 0)
DELTA-SIGMA
DACA
OR
DACB
8
7
6
5
4
3
2
1
0
DELTA-SIGMA
DACA
OR
DACB
Figure 13. DAC1/DAC2 LUT Assignments
In LUT mode, DAC1 and DAC2 are each controlled by
a separate 8-bit, 4°C-resolution, temperature-
addressed LUT. The delta-sigma outputs use a 10-bit
structure. The 8-bit LUTs are either loaded directly into
the MSBs (8:1) or the LSBs (7:0). This is determined by
DAC1TI (Table 02h, Register C3h), DAC2TI (Table 02h,
Register C4h), DAC1TC (Table 02h, Register C6h, bit
6), and DAC2TC (Table 02h, Register C6h, bit 5). See
Figure 13 for more details. The DAC1 LUT (Table 07h)
and DAC2 LUT (Table 08h) registers are nonvolatile
and password-2 protected.
The reference input, REFIN, is the supply voltage for
the output buffer of DAC1 and DAC2. The voltage con-
nected to REFIN must be able to support the edge rate
requirements of the delta-sigma outputs. In a typical
application, a 0.1F capacitor should be connected
between REFIN and ground.
Digital I/O Pins
Five digital input and four digital output pins are provid-
ed for monitoring and control.
LOS, LOSOUT
By default (LOSC = 1, Table 02h, Register 89h), the
LOS pin is used to convert a standard comparator out-
put for loss of signal (LOS) to an open-collector output.
This means the mux shown in the
Block Diagram by
default selects the LOS pin as the source for the
LOSOUT output transistor. The output of the mux can
be read in the STATUS byte (Lower Memory,
Register 6Eh) as the RXL bit. The RXL signal can be
inverted (INV LOS = 1) before driving the open-drain
output transistor using the XOR gate provided. Setting
LOSC = 0 configures the mux to be controlled by LOS
LO, which is driven by the output of the LOS quick trip
(Table 02h, Registers BEh and BFh). The mux setting
(stored in EEPROM) does not take effect until VCC >
POA, allowing the EEPROM to recall.
相关PDF资料
PDF描述
MS27484E18F66S CONN PLUG 66POS STRAIGHT W/SCKT
MS27467E25A24P CONN PLUG 24POS STRAIGHT W/PINS
D38999/24WG11PA CONN RCPT 11POS JAM NUT W/PINS
D38999/26FH21SA CONN PLUG 21POS STRAIGHT W/SCKT
413515-7 CONN JACK BNC RTANG 50OHM 30AU
相关代理商/技术参数
参数描述
DS-187PU 制造商:Shinagawa Shoko 功能描述:
DS-187U 制造商:Shinagawa Shoko 功能描述:
DS1880E-050 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1880E-050/T&R 制造商:Maxim Integrated Products 功能描述:DUAL LOG POT + EQUALIZER T&R - Tape and Reel
DS1880E-050/T&R 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor