- 您现在的位置：买卖IC网 > PDF目录1913 > DS1881Z-050+T&R (Maxim Integrated Products)IC DGTL POT NV 2CH 45K 16-SOIC PDF资料下载
参数资料
| 型号： | DS1881Z-050+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT NV 2CH 45K 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 接片： | 64 |
| 电阻（欧姆）： | 45k |
| 电路数： | 2 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
DS1881
Dual NV Audio Taper Digital Potentiometer
14
____________________________________________________________________
setup time (see Figure 4) before the next rising edge of
SCL during a bit read. The device shifts out each bit of
data on SDA at the falling edge of the previous SCL
pulse and the data bit is valid at the rising edge of the
current SCL pulse. Remember that the master gener-
ates all SCL clock pulses including when it is reading
bits from the slave.
Acknowledgement (ACK and NACK): An Acknowledge-
ment (ACK) or Not Acknowledge (NACK) is always the
9th bit transmitted during a byte transfer. The device
receiving data (the master during a read or the slave
during a write operation) performs an ACK by transmit-
ting a zero during the 9th bit. A device performs a
NACK by transmitting a one during the 9th bit. Timing
(Figure 4) for the ACK and NACK is identical to all other
bit writes. An ACK is the acknowledgment that the
device is properly receiving data. A NACK is used to
terminate a read sequence or as an indication that the
device is not receiving data.
STOP
CONDITION
OR REPEATED
START
CONDITION
REPEATED IF MORE BYTES
ARE TRANSFERRED
ACK
START
CONDITION
ACK
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SLAVE ADDRESS
MSB
SCL
SDA
R/W
DIRECTION
BIT
12
6
7
8
9
12
8
9
3–7
Figure 3. Data Transfer Protocol
SDA
SCL
tHD:STA
tLOW
tHIGH
tR
tF
tHD:DAT
tSU:DAT
REPEATED
START
tSU:STA
tHD:STA
tSU:STO
tSP
STOP
START
tBUF
NOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).
Figure 4. I2C Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| DS1882Z-050+T&R | IC POT DIGIT DL LOG 50K 16SOIC |
| DS1884AT+T | IC SFP PON ONU CTRLR 24TQFN |
| DS2105Z+ | IC SCSI TERMINATOR 16-SOIC |
| DS2106S/T&R | IC TERMINATOR SCSI 28-SOIC |
| DS2108S+T&R | IC TERM SCSI DIFF/SWITCH 24-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1882 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual Log Audio Digital Potentiometer |
| DS1882E-050 | 制造商:Maxim Integrated Products 功能描述:DUAL NV +/-5V AUDIO POT TSSOP-16 - Rail/Tube |
| DS1882E-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV =/-5V AUDIO POT TSSOP 16 T& - Tape and Reel |
| DS1882E-050+ | 功能描述:数字电位计 IC Dual NV Audio Taper RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1882E-050+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 64POS 45KOHM DUAL 16TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DIGIT DL LOG 50K 16TSSOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs Dual NV Audio Taper |
发布紧急采购，3分钟左右您将得到回复。