- 您现在的位置：买卖IC网 > PDF目录97866 > DS21372T (DALLAS SEMICONDUCTOR) SPECIALTY TELECOM CIRCUIT, PQFP32 PDF资料下载
参数资料
| 型号： | DS21372T |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Telecom IC:Other |
| 英文描述： | SPECIALTY TELECOM CIRCUIT, PQFP32 |
| 封装： | TQFP-32 |
| 文件页数： | 16/21页 |
| 文件大小： | 214K |
| 代理商： | DS21372T |
DS21372
4 of 21
DETAILED PIN DESCRIPTION Table 1
PIN
SYMBOL
TYPE
DESCRIPTION
1TL
I
Transmit Load. A positive-going edge loads the pattern generator with
the contents of the Pattern Set Registers. The MSB of the repetitive or
pseudorandom pattern appears at TDATA after the third positive edge of
TCLK from asserting TL. TL is logically OR’ed with PCR.7 and should
be tied to VSS if not used. See Figure 8 for timing information.
2
AD0
I/O
Data Bus. An 8-bit multiplexed address/data bus.
3
AD1
I/O
Data Bus. An 8-bit multiplexed address/data bus.
4
TEST
I
Test. Set high to 3-state all output pins ( INT , ADx, TDATA, RLOS).
Should be tied to VSS to enable all outputs.
5VSS
-
Signal Ground. 0.0 volts. Should be tied to local ground plane.
6
AD2
I/O
Data Bus. An 8-bit multiplexed address/data bus.
7
AD3
I/O
Data Bus. An 8-bit multiplexed address/data bus.
8
AD4
I/O
Data Bus. An 8-bit multiplexed address/data bus.
9
AD5
I/O
Data Bus. An 8-bit multiplexed address/data bus.
10
AD6
I/O
Data Bus. An 8-bit multiplexed address/data bus.
11
AD7
I/O
Data Bus. An 8-bit multiplexed address/data bus.
12
VSS
-
Signal Ground. 0.0 volts. Should be tied to local ground plane.
13
VDD
-
Positive Supply. 3.3 volts.
14
BTS
I
Bus Type Select. Strap high to select Motorola bus timing; strap low to
select Intel bus timing. This pin controls the function of the RD (DS),
ALE(AS), and WR (R/ W ) pins. If BTS = 1, then these pins assume the
function listed in parenthesis ().
15
RD
(DS)
I
Read Input (Data Strobe).
16
CS
I
Chip Select. Must be low to read or write the port.
17
ALE(AS)
I
Address Latch Enable (Address Strobe). A positive going edge serves
to demultiplex the bus.
18
WR
(R/ W )
I
Write Input (Read/Write).
19
INT
O
Alarm Interrupt. Flags host controller during conditions defined in
Status Register. Active low, open drain output.
20
VDD
-
Positive Supply. 3.3 volts.
21
VSS
-
Signal Ground. 0.0 volts. Should be tied to local ground plane.
22
LC
I
Load Count. A positive-going edge latches the current bit and bit error
count into the user accessible BCR and BECR registers and clears the
internal count registers. LC is logically OR’ed with control bit PCR.4.
Should be tied to VSS if not used.
23
RLOS
O
Receive Loss Of Sync. Indicates the real time status of the receive
synchronizer. Active high output.
相关PDF资料 |
PDF描述 |
|---|---|
| DS21372 | SPECIALTY TELECOM CIRCUIT, PQFP32 |
| DS2141AN | DATACOM, FRAMER, PDIP40 |
| DS2141AQN | DATACOM, FRAMER, PQCC44 |
| DS2141AQ | DATACOM, FRAMER, PQCC44 |
| DS2141A | DATACOM, FRAMER, PDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21372T+ | 功能描述:网络控制器与处理器 IC 3.3V Bit Error Rate Tester (BERT) RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21372TN | 功能描述:网络控制器与处理器 IC 3.3V Bit Error Rate Tester (BERT) RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21372TN+ | 功能描述:网络控制器与处理器 IC 3.3V Bit Error Rate Tester (BERT) RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS214 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS2141A | 功能描述:网络控制器与处理器 IC T1 Controller w/Elastic Store RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。