参数资料
型号: DS2151QN
厂商: Maxim Integrated Products
文件页数: 11/60页
文件大小: 0K
描述: IC TXRX T1 1-CH 5V LP IND 44PLCC
标准包装: 1
功能: 单芯片收发器
接口: T1
电路数: 1
电源电压: 4.75 V ~ 5.25 V
电流 - 电源: 65mA
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 44-LCC(J 形引线)
供应商设备封装: 44-PLCC(16.59x16.59)
包装: 管件
包括: 警报检测器和发生器,CSU 回路代码发生器和检测器,DSX-1和CSU 线路补偿发生器
DS2151Q
19 of 60
5 STATUS AND INFORMATION REGISTERS
There is a set of four registers that contain information on the current real time status of the DS2151Q:
Status Register 1 (SR1), Status Register 2 (SR2), Receive Information Register 1 (RIR1), and Receive
Information Register 2 (RIR2). When a particular event has occurred (or is occurring), the appropriate bit
in one of these four registers will be set to a 1. All of the bits in these registers operate in a latched
fashion. This means that if an event occurs and a bit is set to a 1 in any of the registers, it will remain set
until the user reads that bit. The bit will be cleared when it is read and it will not be set again until the
event has occurred again or if the alarm(s) is still present.
The user will always precede a read of these registers with a write. The byte written to the register will
inform the DS2151Q which bits the user wishes to read and have cleared. The user will write a byte to
one of these four registers, with a 1 in the bit positions he or she wishes to read and a 0 in the bit positions
he or she does not wish to obtain the latest information on. When a 1 is written to a bit location, the read
register will be updated with current value and the previous value will be cleared. When a 0 is written to a
bit position, the read register will not be updated and the previous value will be held. A write to the status
and information registers will be immediately followed by a read of the same register. The read result
should be logically ANDed with the mask byte that was just written and this value should be written back
into the same register to ensure that the bit does indeed clear. This second write is necessary because the
alarms and events in the status registers occur asynchronously in respect to their access via the parallel
port. The write-read-write scheme is unique to the four status registers and it allows an external
microcontroller or microprocessor to individually poll certain bits without disturbing the other bits in the
register. This operation is key in controlling the DS2151Q with higher-order software languages.
The SR1 and SR2 registers have the unique ability to initiate a hardware interrupt via the INT1 and INT2
pins, respectively. Each of the alarms and events in the SR1 and SR2 can be either masked or unmasked
from the interrupt pins via the Interrupt Mask Register 1 (IMR1) and Interrupt Mask Register 2 (IMR2)
respectively.
相关PDF资料
PDF描述
DS2152L+ IC TXRX T1 1CHIP ENHNCD 100-LQFP
DS2153Q-A7+T&R IC TXRX E1 1-CHIP 5V 44-PLCC
DS2154LNA2+ IC TXRX E1 5V 100-LQFP
DS2154L IC TXRX E1 1CHIP 5V ENH 100-LQFP
DS2155LN IC TXRX T1/E1/J1 1-CHIP 100-LQFP
相关代理商/技术参数
参数描述
DS2151QN/T&R+ 制造商:Maxim Integrated Products 功能描述:FRAMER DS1/E1/ISDN-PRI/T1 5V 44PLCC - Tape and Reel
DS2151QN/T&R 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2151QNB 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2151QNB/T&R 制造商:Maxim Integrated Products 功能描述:T1 SINGLE CHIP XCVR REV B IND - Tape and Reel
DS2151QNB/T&R 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray