参数资料
型号: DS2154LN+
厂商: Maxim Integrated Products
文件页数: 62/87页
文件大小: 0K
描述: IC TXRX E1 1CHIP 5V ENH 100-LQFP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 90
类型: 收发器
驱动器/接收器数: 1/1
规程: E1
电源电压: 4.75 V ~ 5.25 V
安装类型: 表面贴装
封装/外壳: 100-LQFP
供应商设备封装: 100-LQFP(14x14)
包装: 管件
DS2154
65 of 87
in Table 13-2. The line driver in the DS2154 contains a current limiter that prevents more than 50mA
(RMS) from being sourced in a 1
load.
Table 13-2. Transformer Specifications
SPECIFICATION
RECOMMENDED VALUE
Turns Ratio
1:1 (receive) and 1:1.15 or 1:1.36 (transmit)
±5%
Primary Inductance
600
H minimum
Leakage Inductance
1.0
H maximum
Intertwining Capacitance
40pF maximum
DC Resistance
1.2
maximum
13.3 Jitter Attenuator
The DS2154 contains an on-board jitter attenuator that can be set to a depth of either 32 or 128 bits via
the JABDS bit in the Line Interface Control Register (LICR). The 128-bit mode is used in applications
where large excursions of wander are expected. The 32-bit mode is used in delay sensitive applications.
The characteristics of the attenuation are shown in Figure 13-4. The jitter attenuator can be placed in
either the receive path or the transmit path by appropriately setting or clearing the JAS bit in the LICR.
Also, the jitter attenuator can be disabled (in effect, removed) by setting the DJA bit in the LICR. In order
for the jitter attenuator to operate properly, a 2.048MHz clock (
±50ppm) must be applied at the MCLK
pin or a crystal with similar characteristics must be applied across the MCLK and XTALD pins. If a
crystal is applied across the MCLK and XTALD pins, then capacitors should be placed from each leg of
the crystal to the local ground plane as shown in Figure 13-1. On-board circuitry adjusts either the
recovered clock from the clock/data recovery block or the clock applied at the TCLKI pin to create a
smooth jitter-free clock that is used to clock data out of the jitter attenuator FIFO. It is acceptable to
provide a gapped/bursty clock at the TCLKI pin if the jitter attenuator is placed on the transmit side. If the
incoming jitter exceeds either 120UIP-P (buffer depth is 128 bits) or 28UIP-P (buffer depth is 32 bits), then
the DS2154 will divide the internal nominal 32.768MHz clock by either 15 or 17 instead of the normal 16
to keep the buffer from overflowing. When the device divides by either 15 or 17, it also sets the Jitter
Attenuator Limit Trip (JALT) bit in the Receive Information Register (RIR.5).
相关PDF资料
PDF描述
VE-26W-IU-F2 CONVERTER MOD DC/DC 5.5V 200W
MC100EP16TDG IC RCVR/DRVR ECL DIFF 5V 8SOIC
DS3150Q+T&R IC LIU DS3/E3/STS-1 28-PLCC
DS2450S+ IC CONVERTER A/D QUAD 1-W 8-SOIC
MC100LVEP16DTG IC RECEIVER/DRVR ECL DIFF 8TSSOP
相关代理商/技术参数
参数描述
DS2154LN+ 功能描述:网络控制器与处理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2154LNA2 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2154LNA2+ 功能描述:网络控制器与处理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2154LND2 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2154LND2+ 制造商:Maxim Integrated Products 功能描述:ENHANCED E1 SCT LQFP REVD2 IND LF - Rail/Tube