- 您现在的位置：买卖IC网 > PDF目录378591 > DS2252T Secure Microcontroller Module PDF资料下载
参数资料
| 型号： | DS2252T |
| 英文描述： | Secure Microcontroller Module |
| 中文描述： | 安全微控制器模块 |
| 文件页数： | 5/15页 |
| 文件大小： | 257K |
| 代理商： | DS2252T |
DS2252T
5 of 15
PIN
DESCRIPTION
22
ALE -
Address Latch Enable. Used to de-multiplex the multiplexed Expanded
Address/Data bus on Port 0. This pin is normally connected to the clock input on a ’373
type transparent latch.
XTAL2, XTAL1.
Used to connect an external crystal to the internal oscillator. XTAL1 is
the input to an inverting amplifier and XTAL2 is the output.
GND -
Logic ground.
V
CC
- +5V
.
PROG
-
Invokes the Bootstrap loader on a falling edge. This signal should be debounced
so that only one edge is detected. If connected to ground, the microcontroller will enter
Bootstrap loading on power up. This signal is pulled up internally.
SDI –
Self-Destruct Input. A logic 1 applied to this input causes a hardware unlock. This
involves the destruction of Encryption Keys, Vector RAM, and the momentary removal of
power from V
CCO
. This pin should be grounded if not used.
35, 37
39
2
24
20
INSTRUCTION SET
The DS2252T executes an instruction set that is object code-compatible with the industry standard 8051
microcontroller. As a result, software development packages such as assemblers and compilers that have
been written for the 8051 are compatible with the DS2252T. A complete description of the instruction set
and operation are provided in the User’s Guide section of the Secure Microcontroller Data Book.
MEMORY ORGANIZATION
Figure 2 illustrates the memory map accessed by the DS2252T. The entire 64k of program and 64k of
data are available to the Byte-wide bus. This preserves the I/O ports for application use. An alternate
configuration allows dynamic Partitioning of a 64k space as shown in Figure 3. Any data area not mapped
into the NV RAM is reached via the Expanded bus on Ports 0 and 2. Off-board program memory is not
available for security reasons. Selecting PES=1 provides access to the Real Time Clock as shown in
Figure 4. These selections are made using Special Function Registers. The memory map and its controls
are covered in detail in the User’s Guide section of the Secure Microcontroller Data Book.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2282 | T1 FDL Controller/Monitor Stik |
| DS2411X | Silicon Serial Number with VCC Input |
| DS2411 | Silicon Serial Number with VCC Input |
| DS2411P | Silicon Serial Number with VCC Input |
| DS2431 | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2252T_06 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Soft Microcontroller Module |
| DS2252T_1 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Secure Microcontroller Module |
| DS2252T08-08 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| DS2252T128-08 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| DS2252T-128-12 | 功能描述:模块化系统 - SOM RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
发布紧急采购，3分钟左右您将得到回复。