- 您现在的位置：买卖IC网 > PDF目录1994 > DS2404B (Maxim Integrated Products)IC ECONORAM TIMECHIP 5.5V 16SSOP PDF资料下载
参数资料
| 型号： | DS2404B |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/29页 |
| 文件大小： | 0K |
| 描述： | IC ECONORAM TIMECHIP 5.5V 16SSOP |
| 标准包装： | 77 |
| 系列： | EconoRAM |
| 类型： | 二进制计数器 |
| 特点： | 警报器，方波输出 |
| 时间格式： | 二进制 |
| 数据格式： | 二进制 |
| 接口： | 1 线和 3 线 |
| 电源电压： | 2.8 V ~ 5.5 V |
| 电压 - 电源，电池： | 2.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
DS2404
19 of 29
Interrupts
If the DS2404 detects an alarm condition, it will automatically set the corresponding alarm flag (CCF,
ITF or RTF) in the Status Register. If the flag’s corresponding interrupt bit ( RST , ITE or RTE ) is enabled
(logic 0) an interrupt condition begins as the alarm goes off. The DS2404 signals the interrupt condition
by pulling the open drain IRQ output low. The interrupt condition ceases when the alarm flags are cleared
(i.e., the interrupt is acknowledged by reading the Status Register, address 200H) or if the corresponding
interrupt enable bit is disabled (set to logic 1).
Interrupts can also be generated on the 1-Wire port. Since communication and interrupt signaling share
the same pin, one has to distinguish between two types of interrupts: spontaneous interrupts, called type
1, and delayed interrupts type 2. Spontaneous interrupts that have not yet occurred need to be (re-) armed
by a reset pulse after all communication on the 1-Wire bus has finished. A single falling slope on the
1-Wire bus will disarm this type of interrupt. If an alarm condition occurs while the device is disarmed, at
first a type 2 interrupt will be produced.
Spontaneous interrupts are signaled by the DS2404 by pulling the data line low for 960 to 3840
μs as the
interrupt condition begins (Figure 12). After this long low pulse a presence pulse will follow. If the alarm
condition occurs just after the master has sent a reset pulse, i.e., during the high or low time of the
presence pulse, the DS2404 will not assert its Interrupt Pulse until the presence pulse is finished
(Figure 13).
If the DS2404 cannot assert a spontaneous interrupt, either because the data line was not pulled high,
communication was in progress, or the interrupt was not armed, it will extend the next reset pulse to a
total length of 960 to 3840
μs (delayed interrupt). If the alarm condition occurs during the reset low time
of the reset pulse, the DS2404 will immediately assert its interrupt pulse; thus the total low time of the
pulse can be extended up to 4800
μs (Figure 14). If a DS2404 with a not previously signaled alarm
detects a power-on cycle on the 1-Wire bus, it will send a presence pulse and wait for the reset pulse sent
by the master to extend it and to subsequently issue a presence pulse (Figure 15). As long as an interrupt
has not been acknowledged by the master, the DS2404 will continue sending interrupt pulses.
The interrupt signaling discussed so far is valid for the first opportunity the device has to signal an
interrupt. It is not required for the master to acknowledge an interrupt immediately. If an interrupt is not
acknowledged, the DS2404 will continue signaling the interrupt with every reset pulse. To do so, DS2404
devices of Revision B4 (earlier production parts) will always use the waveform of the Type 2 Interrupt
(Figure 14). Devices of Revision B5 (current production) will either use the waveform of the Type 2
Interrupt (Figure 14) or the waveform of the Type 1A Interrupt (Figure 13). The waveform of the Type 2
Interrupt will be observed after a communication to a device other than the interrupting one; after
successful communication to the interrupting device (without acknowledging the interrupt) the waveform
of the Type 1A Interrupt will be found. The revision code of the DS2404 is appended to the
manufacturing date code, which is printed on the top of the package right below the part number.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2415P+T&R | IC TIME CHIP 1-WIRE 6-TSOC |
| DS2417X/T&R | IC TIMECHIP W/INTRPT 1WIRE CSP |
| DS26502LN+ | IC T1/E1/J1 64KCC ELEMENT 64LQFP |
| DS26503LN+ | IC T1/E1/J1 BITS ELEMENT 64-LQFP |
| DS3105LN+ | IC TIMING LINE CARD 64-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2404B/T&R | 制造商:Maxim Integrated Products 功能描述:ECONORAM/TIME, SSOP16-TRL (GENERIC) - Tape and Reel |
| DS2404B+ | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 512BYTE 16SSOP - Rail/Tube |
| DS2404B+T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 512BYTE 16SSOP - Tape and Reel |
| DS2404FP000 | 制造商:Thomas & Betts 功能描述:200A,CON,3P4W,MG,404,3P480V |
| DS2404FP000/DF2029 | 制造商:Thomas & Betts 功能描述:RS DS2404FP000/DF2029 200A,CON,3P4W |
发布紧急采购，3分钟左右您将得到回复。