- 您现在的位置：买卖IC网 > PDF目录378591 > DS2450S 1-Wire Quad A/D Converter PDF资料下载
参数资料
| 型号： | DS2450S |
| 英文描述： | 1-Wire Quad A/D Converter |
| 中文描述： | 1线四通道A / D转换器 |
| 文件页数： | 2/24页 |
| 文件大小： | 523K |
| 代理商： | DS2450S |
DS2450
2 of 24
102199
the comparison. Each A/D conversion is initiated by the bus master. A channel not used as analog input
can serve as a digital open-drain output. After disabling the input the bus master can directly switch on or
off the open-drain transistor at the selected channel. All device settings are stored in SRAM and kept
non-volatile while the device gets power either through the 1-Wire bus or through its V
CC
pin. After
powering up a power-on reset flag signals the bus master the need to restore the device settings before the
regular operation can resume. All device registers and conversion read-out registers are organized as
three 8-byte memory pages similar to the Status Memory of a DS2505/6 device. An on-chip CRC16
generator protects the communication against transmission errors when reading through the end of a
memory page as well as when writing individual bytes.
OVERVIEW
The block diagram in Figure 1 shows the major function blocks of the device. The DS2450 contains a
factory-lasered registration number that includes a unique 48-bit serial number, an 8-bit CRC, and an 8-
bit family code (20H). The 64-bit ROM portion of the DS2450 not only creates an absolutely unique
electronic identification for the device itself but also is a means to locate and address the device in order
to exercise its control functions.
The device gets its power either from the 1-Wire bus or through its V
CC
pin. Without a V
CC
supply the
device stores energy on an internal capacitor during periods where the signal line is high and continues to
operate off of this “parasite” power source during the low times of the 1-Wire line until it returns to high
to replenish the parasite (capacitor) supply. This, however, provides sufficient energy only for
communication. To perform an A/D conversion a strong pullup of the 1-Wire bus to 5V or a V
CC
supply
is required.
DS2450 BLOCK DIAGRAM
Figure 1
相关PDF资料 |
PDF描述 |
|---|---|
| DS2480 | Serial 1.Wire Line Driver |
| DS2480S | Serial 1.Wire Line Driver |
| DS2490 | USB to 1-Wire Bridge Chip |
| DS2490S | USB to 1-Wire Bridge Chip |
| DS2502-E64 | IEEE EUI-64 Node Address Chip |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2450S/T&R | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS2450S+ | 功能描述:模数转换器 - ADC Quad 1-Wire RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS2450S+ | 制造商:Maxim Integrated Products 功能描述:SEMICONDUCTOR ((NW)) |
| DS2450S+T&R | 制造商:Maxim Integrated Products 功能描述:IC CONVERTER A/D QUAD 1-W 8-SOIC |
| DS2450S+T&R | 功能描述:模数转换器 - ADC Quad 1-Wire RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。